Icom IC-M220 Instruction Manual Download Page 31

Page: 31 / 66

DIGITAL SELECTIVE CALLING (DSC)

Sending an Individual Acknowledgement

When you have received an Individual call (p. 29)

, send an Acknowledgement to the

calling station. When the Auto Ack is set to “Manual,” you can select an appropriate

acknowledgement type.

1. While an Individual call is being received, push

ALARM OFF

to turn OFF the alarm.

•The received call’s information is displayed.

2. Push

ACPT

•

The Acknowledgement category screen is displayed.

If you want to send an Acknowledgement “Able to

comply” right away, push

ABLE

If you cannot communicate, and want to return to the

operating screen, push

IGN

3. Push

ABLE

UNABLE

, or

NEW CH

to select the

Acknowledgement type.

ABLE

(Able to

Comply)

Sends an Acknowledgement without any

changes.

UNABLE

(Unable to

Comply):

Sends an Acknowledgement but cannot

communicate.

NEW CH

(Propose

New CH)

Able to communicate but proposes

another channel. Specify the channel by

pushing [▲] or [▼].

(Example: Channel 69)

4. Push

CALL

to send the Acknowledgement.

Summary of Contents for IC-M220



































































Search results

Summary of Contents for IC-M220

Reviews:

Brands by name

Popular brands

Icom IC-M220, Instruction Manual

Search results

Summary of Contents for IC-M220

Reviews:

Brands by name

Popular brands