background image

Battery Charging and Battery Case

16

IMPORTANT!: Battery charging

Ensure the guide lobs on the battery pack are correctly 
aligned with the guide rails inside the charger adapter.
(This illustration is described with the BC-160.)

Lobs

Guide rail

Optional battery case (BP-240)

When using the optional battery case, install 6 ×

 

AAA 

(LR03) size alkaline batteries as illustrated at right.

Unhook the battery cover release hook (

n

), and open 

the cover in the direction of the arrow (

o

. (Fig.1)

Then, install 6 ×

 

AAA (LR03) size alkaline batteries. 

(Fig.2)

Install the alkaline batteries only.

Be sure to observe the correct polarity.

Do not pin the ribbon under the batteries.

Fit the cover in the direction of the arrow (

p

), then 

close (

q

). And hook the battery cover release hook until 

it makes a ‘click’ sound (

r

). (Fig.3)

CAUTION:

When installing batteries, make sure they are all the 

same brand, type and capacity. Also, do not mix new and 
old batteries together.

Keep battery contacts clean. It’s a good idea to clean 

battery terminals once a week.

Never incinerate used battery cells since internal 

battery gas may cause them to rupture.

Never expose a detached battery case to water. If the 

battery case gets wet, be sure to wipe it dry before using 
it.

Fig.3

Fig.2

Fig.1

BP-240

Battery caution

DANGER Charge the specified Icom batteries only. Only 
tested and approved for use with genuine Icom 
batteries. Fire and/or explosion may occur when a third 
party battery pack or counterfeit product is charged.
CAUTION! NEVER insert battery pack/transceiver (with 
the battery pack attached) in a wet or soiled condition 
into the charger. This may result in corrosion of the 
charger terminals or damage to the charger. The charger 
is not waterproof and water can easily get into it.
NEVER incinerate used battery packs. Internal battery 
gas may cause an explosion.
NEVER immerse the battery pack in water. If the battery 
pack becomes wet, be sure to wipe it dry BEFORE 
attaching it to the transceiver.
NEVER short the terminals of the battery pack. Also, 
current may flow into nearby metal objects, such as a 
necklace, etc. Therefore, be careful when carrying with, 
or placing near metal objects, carrying in handbags, etc.
AVOID leaving the battery pack in a fully charged, or 
completely discharged condition for long time. It causes 
shorter battery life. In case of leaving the battery pack 
unused for a long time, it must be kept safely after 
discharge, or use the battery until the battery indicator 
appears, then remove it from the transceiver. If your 
battery pack seems to have no capacity even after being 
charged, fully charge the battery pack again.
If the batteries still do not retain a charge (or very little), 
new battery pack must be purchased.

Summary of Contents for IC-F4062S








































Reviews: