3 - 12
3-5 SCOPE CIRCUITS
3-5-1 SCOPE RECEIVER CIRCUIT (SCOPE UNIT)
A portion of the 64.455 MHz 1st IF signal from the 1st
mixer circuit (RXPLL-A/B units; IC1051, Q1211, Q1212:
while receiving) or IF amplifier (MAIN unit; Q506: while
transmitting) passes through the switches (IC1, IC31). The
switched signal is passed through the PIN attenuator (D1,
D2), low-pass filter (L13, L14, C42–C46) and bandpass
filter (L5, L6, C11–C13, C41) and then amplified at the
IF amplifiers (Q2). The amplified signal is mixed with the
18.455–20.455 MHz scope 2nd LO (S2LO) signal at the
mixer circuit (D101) to produce the 45 MHz IF signal. The
mixed IF signal is passed through the ceramic bandpass
filter (FI201) to suppress unwanted signals. The filtered
IF signal is applied to other mixer (D4) after amplifying
at 2 amplifiers (Q201, Q202). The signal is applied to the
amplifier (IC401, pin 6), and then passes through the low-
pass filter (IC403, pins 1, 6). The filtered signal is amplified
at the amplifier (IC404, pin 6), and is then applied to the
DSP IC (IC601) via the A/D converter (IC501, pin 43). The
DSP IC analyzes digital signals, and then outputs digital
data to the CPU.
3-5-2 SCOPE UNIT AGC CIRCUIT (SCOPE UNIT)
A pert of the filtered signal at the low-pass filter (IC403, pin
1) is applied to the amplifier (IC404, pin 6). The amplified
signal is applied to the AGC detector (D401, D402), and
is then applied to the AGC amplifier (IC405, pin 2). The
amplified signal is applied to the comparator section to
compare with “ATTV” signal. The signal is amplified at
the AGC amplifier (Q1), and is then applied to the PIN
attenuator (D1, D2) to keep same gain.
3-5-3 SWEEP LO CIRCUIT (SCOPE UNIT)
The 40 MHz signal is applied to the J3 from the RXPLL-B
unit. The signal is used for reference system clock of each
circuits.
(1) S2 LO CIRCUIT
The 40 MHz reference system clock is amplified at the
amplifiers (Q701 and Q720). The amplified signal is applied
to the 14 bits DDS IC (IC820, pin 62). The DDS IC which is
controlled by the CPU outputs 19.555 MHz (for MAIN RX)
or 19.555±0.5 MHz (for SUB RX) system clock from pin 45,
and then passes through the low-pass filter (L761–L763,
C761–C767), high-pass filter (L764, C768–C770) and
attenuator (R764–R766). The attenuated signal is applied
to the LO amplifier (Q101), and then passes through the
low-pass filter (L104, C108–C110) and attenuator (R105–
R107). The attenuated signal is applied to the mixer circuit
(D101) as S2 LO signal (19.555–20.455 MHz).
(2) S3 LO CIRCUIT
The 40 MHz reference system clock is amplified at the
amplifiers (Q701, Q810). The amplified signal is applied
to the PLL IC (IC801, pin 8). The applied signal passes
through the 1/400 divider and phase detector circuits of
the IC, and is then applied to the VCO circuit (Q821) via
the loop filter to produce 44.8 MHz signal. The 44.8 MHz
signal is amplified at the buffer amplifiers (Q841–Q843),
and then passes through the low-pass filter (L851, L852,
C852–C856) to suppress high-harmonics components. The
filtered signal passes through the attenuator (R856–R858),
and is then amplified at the amplifier (Q301). The signal
passes through the other attenuator (R302–R304), and is
then applied to the mixer circuit (D4) as S3 LO signal.
IC602,
IC603
Scope IN/OUT, SOXD,
SFSR1, SFSX1, SOR1, CLR1
ATT
Q101
IC820
Q720
DDS IC
ATT
Q841
A/D
DSP
Q301
Q821
Q810
Q701
40 MHz signal from
the RXPLL-B unit
IC801
IC1
IC31
D1, D2
Q2
D101
FI201
D4
IC404
IC403
Q202
DET
D401, D402
Q842,
Q843
IC501
IC601
IC405
Q1
IC404
Pin
ATT
RX-A SIF IN
RX-B SIF IN
TX SCOPE
"ATTV" signal
1/448
Phase
detector
1/400
• SCOPE CIRCUIT
