ICI Caldaie FX N Series Installation, Use And Maintenance Manual Download Page 3

Page: 3 / 32

General information

General information

INTRODUCTION

Dear Customer,
Thank you for having chosen an appliance of the series

FX N

, a high quality and efficiency product, reliable and safe.

We recommend entrusting its maintenance to

Professionally Qualified Personnel

who, when necessary, uses original spare parts.

This manual contains important information and suggestions that must be observed for easier installation and best possible use
of the appliance.

IMPORTANT

Failure to observe the instructions in this manual will void the warranty conditions.

RANGE

MODEL

CODE

FX 50 N

86014065

FX 100 N

86014115

FX 150 N

86014165

FX 100 DUAL N (FX50 N + FX50 N)

86014113

FX 200 DUAL N (FX100 N + FX100 N)

86014215

FX 300 DUAL N (FX150 N + FX150 N)

86014315

COMPLIANCE

The steam generators Series

FX N

comply with the following European Directives:

–

Directive 2014/68/EU (PED)

–

Low Voltage Directive 2014/35/EU

–

Electromagnetic Compatibility Directive 2014/30/EU

–

UNI TS 11325-3

NOTE

The serial number is indicated on the boiler nameplate.

Cooke Industries - Phone: +64 9 579 2185 Email: [email protected] Web: www.cookeindustries.co.nz

Summary of Contents for FX N Series

































Search results

Summary of Contents for FX N Series

Reviews:

Related manuals for FX N Series

Brands by name

Popular brands

ICI Caldaie FX N Series, Installation, Use And Maintenance Manual

Search results

Summary of Contents for FX N Series

Reviews:

Related manuals for FX N Series

Brands by name

Popular brands