background image

2

Dear customers;

Contents

Acknowledgment

Method of Use

Cautions for your safety       
  - Power supply related items                        
  - Installation related items                   
  - During use
Part names and controllers

3~4

4        
5

6~7

8
9

10

11
11
12

Check prior to use             
Button display names and functions                      
How to make soft ice cream      
Conversion function between
ice-cream mode and yogurt mode
How to set non-load 
Carburetor control

Thank you very much for purchasing a soft ice cream maker made by ICETRO. For correct use of the 
product  and  its  maintenance,  please  read  this  manual  carefully.  If  a  problem  occurs  while  using  the 
product, you can refer to this manual for troubleshooting. This manual contains a product warranty, so 
keep it safely for future reference. This product can be installed only by someone qualified for installation.
If use of parts and accessories not provided or approved by ICETRO or any part or accessories made 
by ICETRO but remodeled by other person causes a problem, we are not responsible for it financially.         
(The  functions  and  specifications  shown  in  this  manual  and  on  the  web  site  are  subject  to  change 
without notice. Please visit our website at http://www.icetro.com to obtain the latest specifications.

Cleaning Method

13~14 

15   

 15

16
17

Cleaning Method                
- Wash mode                   
- Washing of each parts
- Condenser and filter cleaning method                           
Dasher cover assembly method     
- Dasher cover assembly
- Dasher and dasher cover

ETC

18
19
20
21
22
23

24~27

28
29

Installation method
- Electrical connection
Before requesting service                        
Error code types                          
Circuit diagram                

 

Product specification 
Refrigerant circuit 

 

Part list
What to watch out for
Warranty

Summary of Contents for ISI-163SB

































Reviews: