background image

77

GENERAL SAFETY REGULATIONS 

The regulations illustrated below must be carefully followed in order to avoid harm to the operator and 

damage to the machine. 

Read the labels on the machine carefully. Do not cover them for any reason and replace them immediately 

if they become damaged. 

The machine must be used exclusively by authorised, trained personnel. 

During the working of the machine, pay attention to other people and especially to children. 

The machine is not suitable for cleaning carpets. 

The socket for the battery charger cable must have a prescribed earth connection.

Avoid damaging the battery charger cable by crushing or bending it, or by applying stress. 

If you notice any damage to the battery charger cable, contact a 

ICE

technical assistance centre 

immediately.

Do not mix different types of detergent as this may produce harmful gases. 

Do not place any liquid containers on the machine. 

The machine is designed for dry use only and should not be used or kept outdoors in wet conditions 

The storage temperature must be between -25

C and +55

C; do not store outdoors in damp conditions. 

Conditions of use: room temperature between 0

C and 40

C with relative humidity between 30 and 95%. 

Do not use the machine in an explosive atmosphere. 

Do not use the machine as a means of transport. 

Do not use acid solutions which may damage the machine. 

Avoid working with the brushes when the machine is standing still, so as not to damage the floor. 

Do not vacuum inflammable liquids. 

Do not use the device to collect dangerous powders. 

In the event of a fire, use a powder extinguisher. Do not use water. 

Do not knock against shelving or scaffolding, where there is a danger of falling objects. 

If you use the machine where there is a risk of falling objects, the machine must be equipped with 

protection devices against falling objects 

Do not use the machine on surfaces with an inclination greater than the one shown on the plate. 

The machine is designed to carry out the washing and drying operations simultaneously. Different 

operations should only be carried out in areas where the passage of unauthorised persons is prohibited. 

Signal the presence of damp floors with suitable signs. 

If the machine does not work properly, check this is not caused by failure to carry out routine maintenance. 

Otherwise, request the intervention of the

 ICE

 technical assistance centre. 

If you need to replace any components, request the ORIGINAL spare parts from a 

ICE

 dealer and/or 

Authorised Retailer. 

Before carrying out any maintenance work, switch off the machine and disconnect the battery connector. 

Do not remove any protection devices which require the use of tools in order to be removed. 

Do not wash the machine with direct water jets or with pressurised water, nor with corrosive substances. 

Have the machine checked by a 

ICE

 technical assistance centre every year. 

To prevent scaling in the solution tank filter, do not fill the tank with detergent solution many hours before 

using the machine. 

Before using the machine, check that all the hatches and covers are positioned as shown in this Use and 

Maintenance Manual. 

Summary of Contents for SCRUB 35D





























Reviews: