ICC ETH-1000, Installation Manual

Page: 3 / 54

3
INTRODUCTION INTRODUCTION
New building construction and energy saving techniques have driven
the need for improved communications between appliances and
building environmental systems. There are several different protocols
WKDWKDYHGHYHORSHGIRUDFFRPSOLVKLQJWKLVWDVNLQFOXGLQJ%$&QHW
and Modbus. Since appliances come with a variety of controls,
interfacing with the various protocols presents different challenges.
,QGXVWULDO&RQWURO&RPPXQLFDWLRQV,&&KDVGHYHORSHGWKHGHYLFHV
to act as a communication gateway allowing appliances to
communicate to the different building management protocols. The
ICC module translates the appliance codes and commands into the
appropriate protocol language giving the end user the ability to
monitor and control the appliance. The end user will be able to adjust
DQGPRQLWRUWKHHTXLSPHQWDQGREWDLQEHWWHUOHYHOVRIHI¿FLHQF\DQG
cost savings.
The ICC module in this kit has been designed to seamlessly integrate
with the water heater controls. Once the unit is connected to the
control and to the energy management system, the user will be able
WRRSHUDWHWKHXQLWZLWKWKH%XLOGLQJ0DQDJHPHQWV\VWHPLQWHUIDFH
WARNINGS
When installing the unit, ensure that all power is off before opening
any water heater enclosure. Failure to do so could result in electrical
VKRFNDQGRUSRVVLEOHGDPDJHWRWKHXQLW
Do not install in areas of high temperature, in excess of 167° F. Install
in areas not subject to water or excess moisture.
PARTS
Table 1. Parts Required
Item Ethernet Serial (RS-485)
ICC Module
; ;
Communication Cable
; ;
Power Adapter
; ;
Jumpers 4 4
Splitter
; ;
86%.H\ ; ;
TOOLS REQUIRED
Wire Cutters
• 24 AWG Wire Stripper
•
PP)ODW%ODGH6FUHZ'ULYHU
GENERAL GUIDELINES
The module should be installed as close as practical to the water
heater control.
The ICC module uses a 120 Volt power adapter to supply 9 volts
DC for the unit. One 120 VAC outlet is required for each module
installed. The power adapter comes with a six foot length of wire. If
additional wire is needed, extra wire may be added, in accordance
with local ordinances for installation of low voltage wire.
7KH,&&*DWHZD\NLWFRQWDLQVD86%NH\ZLWKWKH,&&&RQ¿JXUDWLRQ
6WXGLRSURJUDPDOOFRQ¿JXUDWLRQ¿OHVSDUDPHWHUOLVWVDQGLQVWUXFWLRQV
UHTXLUHGWRLQVWDOODQGFRQ¿JXUHWR\RXUZDWHUKHDWHUERLOHUDQG%06
system.
%HIRUHSOXJJLQJLQWKH,&&*DWHZD\LQVWDOOWKH,&&&RQ¿JXUDWLRQ
6WXGLRIURPWKH86%NH\DQGUXQWKHSURJUDP2QFHUXQQLQJVHOHFW
)LOH 2SHQ 3URMHFW DQG EURZVH WR WKH 86% NH\ DQG VHOHFW WKH
FRQ¿JXUDWLRQ¿OHZKRVHQDPHPDWFKHVWKHJDWHZD\
%HFDXVHVRPH86%KXEVPD\QRWVXSSO\VXI¿FLHQWFXUUHQWWRUXQ
the Gateway, insure that the ICC Gateway is connected to the power
DGDSWHU 7KHQ FRQQHFW WKH ,&& *DWHZD\ XVLQJ WKH 86% FDEOH
provided. Run the ICC Gateway Studio application from the start
menu.
(DFKFRQ¿JXUDWLRQKDVGHIDXOWDGGUHVVDQG%$&QHWLQVWDQFHVHWWLQJV
that can be changed. For Mirius gateways, the default Modbus
DGGUHVVLVDQGWKHGHIDXOW%$&QHWDGGUHVVLV)RUJDVPRGHOV
WKH GHIDXOW %$&QHW ,QVWDQFH 1XPEHU LV DQG IRU HOHFWULF
models the default instance number is 530081. For Ethernet
Gateways, the default setting is to acquire an IP address automatically
IURPWKHURXWHU'+&3,IDVWDWLF,3DGGUHVVLVGHVLUHGWKLVFDQDOVR
be set. To change these addresses and communication settings,
XVHWKH,&&&RQ¿JXUDWLRQ6WXGLRDSSOLFDWLRQSURJUDP7KHODWHVW
version of this application program can be downloaded from:
ZZZLFFGHVLJQVFRPLFFFRQ¿JXUDWLRQVWXGLRKWPO
%HIRUHPDNLQJDQ\FKDQJHVLWLVUHFRPPHQGHGWRVDYHWKHLQVWDOOHG
FRQ¿JXUDWLRQSURMHFWXVLQJWKHGLVNLFRQRU
File -> Save Project As
, then
JLYHLWDQDPHDQGVHOHFWWKHIROGHU¿QDOO\SUHVV Save
.
To change the Instance number and the Device Name, scroll down
and select the Device Object and replace the text in the boxes in
the upper right corner.
Figure 1. Changing Instance Number and Device Name
)RU(7+(WKHUQHWLQWHUIDFHWKH,3VHWWLQJVLQFOXGLQJ'+&3
Static, the IP address and authentication can be changed by selecting
Ethernet from the upper left hand window and changing the text and
drop down list selection similar to changing the Instance number
above.
)RU0LULXV56$LQWHUIDFHIRU%$&QHW0673RU0RG%XV578
the baud rate and other serial communication parameters can be
changed by scrolling down to and selecting
RS-485 A -> ModBus RTU
Slave
.