40
BACnet / Boilers
Table 37. Lock and Hold Codes
Code
Description
Recommended Troubleshooting of Lockout Codes
151
+LJK¿UHVZLWFK21
2(06SHFL¿F
1. Check wiring and correct any potential wiring errors.
2.
&KHFN+LJK)LUH6ZLWFKWRDVVXUHSURSHUIXQFWLRQQRWZHOGHGRUMXPSHUHG
3. Manually drive the motor to the High Fire position and adjust the HF switch
while in this position and verify voltage through the switch to the HFS input with
a voltmeter.
4. If steps 1-3 are correct and the fault persists, replace the module.
152
Combustion pressure ON
2(06SHFL¿F
1. Check wiring and correct any errors.
2. Inspect the Combustion Pressure Switch to make sure it is working correctly.
3. Reset and sequence the relay module.
4.
'XULQJ67$1'%<DQG35(385*(PHDVXUHWKHYROWDJHEHWZHHQ7HUPLQDO
-DQG/16XSSO\YROWDJHVKRXOGEHSUHVHQW,IQRWWKHORFNRXWVZLWFKLV
defective and needs replacing.
5. If the fault persists, replace the relay module.
153
Combustion Pressure Off
154
Purge Fan switch On
2(06SHFL¿F
1. Purge fan switch is on when it should be off.
155
Purge Fan switch Off
156
Combustion pressure and Flame ON
2(06SHFL¿F
1.
&KHFNWKDWÀDPHLVQRWSUHVHQWLQWKHFRPEXVWLRQFKDPEHU&RUUHFWDQ\HUURUV
2.
0DNHVXUHWKDWWKHÀDPHGHWHFWRULVZLUHGWRWKHFRUUHFWWHUPLQDO
3.
0DNHVXUHWKH) *ZLUHVDUHSURWHFWHGIURPVWUD\QRLVHSLFNXS
4.
5HVHWDQGVHTXHQFHWKHPRGXOHLIFRGHUHDSSHDUVUHSODFHWKHÀDPHGHWHF
-
tor.
157
Combustion pressure and Flame OFF
158
Main valve ON
2(06SHFL¿F
1. Check Main Valve terminal wiring and correct any errors.
2. Reset and sequence the module. If fault persist, replace the module.
159
Main valve OFF
160
Ignition ON
2(06SHFL¿F
1. Check Ignition terminal wiring and correct any errors.
2. Reset and sequence the module. If fault persist, replace the module.
161
Ignition OFF
162
Pilot valve ON
2(06SHFL¿F
1. Check Pilot Valve terminal wiring and correct any errors.
2. Reset and sequence the module. If fault persist, replace the module.
163
Pilot valve OFF
164
%ORFNLQWDNH21
2(06SHFL¿F
1. Check wiring and correct any errors.
2.
,QVSHFWWKH%ORFN,QWDNH6ZLWFKWRPDNHVXUHLWLVZRUNLQJFRUUHFWO\
3. Reset and sequence the module.
4. During Standby and Purge, measure the voltage across the switch. Supply
YROWDJHVKRXOGEHSUHVHQW,IQRWWKH%ORFN,QWDNH6ZLWFKLVGHIHFWLYHDQG
needs replacing.
5. If the fault persists, replace the relay module.
165
%ORFNLQWDNH2))
166-171
RESERVED
Feedback Codes
172
Main relay feedback incorrect
Internal Fault.
1. Reset Module.
2. If fault repeats, replace module.
173
Pilot relay feedback incorrect
174
Safety relay feedback incorrect
175
Safety relay open
176
Main relay ON at safe start check
177
Pilot relay ON at safe start check
178
Safety relay ON at safe start check
179-183
RESERVED
Parameter Faults
184
,QYDOLG%/2:(5+6,RXWSXWVHWWLQJ
3.
5HWXUQWR&RQ¿JXUDWLRQPRGHDQGUHFKHFNVHOHFWHGSDUDPHWHUVUHYHULI\DQG
reset module.
4. If fault repeats, verify electrical grounding.
5. If fault repeats, replace module.
185
Invalid Delta T limit enable setting
186
Invalid Delta T limit response setting
187
Invalid DHW high limit enable setting
188
Invalid DHW high limit response setting
189
Invalid Flame sensor type setting
190
Invalid interrupted air switch enable setting
191
Invalid interrupted air switch start check enable setting
192
Invalid igniter on during setting
193
Invalid ignite failure delay setting
Summary of Contents for ETH-1000
Page 53: ...53 NOTES NOTES...