ICC ETH-1000 Instruction Manual Download Page 13 | Manualshive

Page: 13 / 281

background image

12

ICC

Note that not all protocols support every baud rate listed above. Refer to section
11 for more information.

Field-Upgradeable

As new firmware becomes available, the gateway can be upgraded in the field by
the end-user. Refer to section 8.1 for more information.

USB Interface

The gateway can be connected to a PC via a USB mini type-B cable. This
simultaneously supplies power while providing the ability to configure the
gateway, monitor data, and update firmware on the device using the ICC
Gateway Configuration Utility. Refer to section 8.1 for more information.

Power over Ethernet (PoE) Enabled

The gateway can be externally powered according to the PoE specification (IEEE
802.3af). Refer to section 5.2 for more information.

Alarm Evaluation with Email Notification

The gateway can autonomously monitor any database address and send emails
to up to four recipients when a certain condition is detected. Alarm conditions
have both value and time constraints, and can be configured to retrigger at a
fixed interval as long as the alarm condition continues to be satisfied. Twenty
individually-configurable alarms are available. Refer to section 10.17 for more
information.

Embedded Web Server

The gateway supports real-time web browser-based interaction via an Adobe®
Flash Player plug-in. This includes support for configuration, database
interaction, and a dashboard GUI with multiple windows, each of which can be
configured to display data in a variety of meter/graph/gauge formats. Refer to
section 10 for more information.

User-Configurable Network Timeouts

The gateway can be configured to perform a specific set of actions when network
communications are lost. This allows each address in the database to have its
own unique “fail-safe” condition in the event of network interruption (support for
this feature varies depending on the protocol). Refer to section 10.19 for more
information.

Flexible Mounting Capabilities

The gateway includes all hardware for desktop, panel/wall and DIN-rail mounting
capabilities. Refer to section 6.1 for more information.

«
...
11
12
13
14
15
...
»

Summary of Contents for ETH-1000


























































































































































































































































































Reviews:

No comments

Related manuals for ETH-1000

Brand: National Instruments Pages: 15

Brand: OlenCom Pages: 299

Brand: RTA Pages: 68

SBO500 SBO Series

Brand: Synway Pages: 72

P-873HNU(B)-51B

Brand: ZyXEL Communications Pages: 12

AIG-501-T-AZU-LX

Brand: Moxa Technologies Pages: 8

IZAR IoT GATEWAY Compact

Brand: Diehl Pages: 4

Brand: RTA Pages: 81

ThingPark Partner

Brand: Actility Pages: 4

Brand: UfiSpace Pages: 27

Brand: SICK Pages: 60

lpnGate LoRaWAN

Brand: LPN Plant Pages: 20

Brand: Avaya Pages: 30

Brand: Avaya Pages: 72

CG-ARM7/GTI HS/LS

Brand: EMS Pages: 22

Brand: EMS Pages: 22

Hot Spot WSG-403

Brand: Planet Networking & Communication Pages: 125

Brand: 2Wire Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands