background image

 

 
                                                                                                                                                                                
                                                                                                                                                                  

 
 

                                                          

16 

 

Manual     ISM

 

 

usb.1 / .2 

 

 

Now, please click 

Spectrum analysis

 to start the RSSI analysis : 

 

 

 

The dialogue shows the current signal strengths in the used frequency range. In this way you can see if 
there are additional radio signals in the frequency range which might prevent the radio receiver from 
receiving the measuring values or superimpose its radio signal. If this is the case, please try to place the 
radio receiver in an area without interferences. 
The example above shows the background noise on all frequencies and a weak signal at about  
434.4 MHz. Both will in this strength not influence the receiving of values from the ISM or IBRit-rf1 radio 
modules. 
But a stronger signal might interfere with the communication, even if it is at 434.4 MHz. 
 

 

 

Note :

 

Because the communication between ISM or IBRit-rf1 radio transmitter and radio receiver is 

 

   

bidirectional, you should additionally do an RSSI measurement in the work area of the radio 

 

   

transmitter. In this way you can determine if there are radio signals that could interfere with 

 

   

the communication between transmitter and receiver.

 

 

Summary of Contents for ISM-usb.1





















Reviews: