e.
Align the one-pin section of the support on the front of the vertical rail
with the middle hole in EIA unit 1.
Note:
Tilt the bridge tool towards the back of the cabinet approximately
45° to make it easier to align the two-pin and one-pin sections with the
vertical support.
f.
Lock the shelf into position.
8.
For the upper SAN768B-2, install the bridge tool by completing the following
steps:
a.
Remove the bridge tool from its box and adjust the two supports 45°.
b.
Hold the bridge tool between the two vertical supports near EIA unit 20.
c.
Move the two supports another 45°. Make sure that the following
conditions are met:
v
The two-pin section of the support is on the back of the vertical support.
v
The one-pin section of the support is on the front of the vertical support.
d.
Align the two-pin section of the support on the back of the vertical rail
with the bottom and middle holes in EIA unit 20.
e.
Align the one-pin section of the support on the front of the vertical rail
with the middle hole in EIA unit 18.
f.
Lock the shelf into position.
9.
Locate the anti-tip bars and if they are not attached, attach them to the lift
tool. If anti-tip bars were previously attached, skip to step 10.
a.
Pull up on the leg-lock pins and insert the anti-tip bars inside the legs.
b.
Pull on the legs and anti-tip bars to ensure that they are locked into
position.
c.
Raise the platform to allow enough room to attach the anti-tip bracket.
d.
Secure the anti-tip bars with the anti-tip bracket and bolt.
10.
Move the lift tool to a position near the rear of the cabinet.
11.
Turn the winch crank clockwise to raise the switch. Move the lift tool into
position in front of the cabinet while you align the 24-inch load plate with the
line on the bridge tool.
12.
Turn the winch crank counterclockwise 1/4 turn to set the winch brake.
13.
Set the wheel brake. Place the wheel chocks around the wheels.
svc00169
55 kg ( 121.2 lbs)
CAUTION:
A fully populated SAN768B-2 weighs approximately 159.2 kg (351 lb)
and requires a minimum of two people and a lift tool to install it.
(C011)
P/N 18P5850-B
SJ000752
CAUTION:
A pinch point exists between the load plate and the bridge tool.
14.
Slide the SAN768B-2 from the cabinet onto the 24–inch load plate. Center the
SAN768B-2 on the platform.
15.
Install the retention straps.
16.
Remove the wheel chocks, release the wheel brake, and move the lift tool
away from the cabinet.
Chapter 2. Installing a SAN768B-2 in a cabinet
33
Summary of Contents for SAN768B-2
