IBM FC EJ05 Manual Download Page 42 | Manualshive

Page: 42 / 66

background image

Figure 21. Attaching the low-profile tailstock to a PCIe adapter

15. If the new adapter is a 4-Port 10/100/1000 Base-TX PCI Express adapter, first engage the tailstock

with the tabs on the card hardware. After the tailstock is attached, secure the tailstock with its screw.

16. If the new adapter is an Ethernet or Fibre Channel adapter, you must attach the SFP transceivers

after you replace the tailstock.
To attach the SFP transceivers, complete the following steps:

a) Place the card flat on a static-protective surface.

b) Slide the transceiver (A) into the adapter hardware.

c) With the latch (B) in the open position, push the latch by rotating it up and toward the card as

shown in Figure 22 on page 29.

d) Repeat for the other transceiver.

28 Power Systems: PCIe adapters for the 9080-M9S

«
...
40
41
42
43
44
...
»

Summary of Contents for FC EJ05



































































Reviews:

No comments

Related manuals for FC EJ05

Brand: quadient Pages: 2

Brand: Uconnect Pages: 3

Brand: X-Micro Pages: 16

Brand: TEXIO Pages: 49

Brand: J5create Pages: 2

Brand: StarTech.com Pages: 10

Brand: TRENDnet Pages: 2

Brand: tams elektronik Pages: 21

Brand: Becker Pages: 4

Brand: 3idee Pages: 7

Brand: Avaya Pages: 2

Powerline 1300 AV2 Adapter

Brand: TRENDnet Pages: 26

Brand: Conceptronic Pages: 16

Brand: Hama Pages: 20

Brand: Lindy Pages: 8

Brand: MSI Pages: 162

Brand: SP Controls Pages: 2

Brand: TEN Technology Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands