IBM FC EJ05 Manual Download Page 46

Page: 46 / 66

Procedure

1. Log in to the system unit as root user.
2. Insert the media containing the device driver software (for example, the CD) into the media device.

If your system does not have a CD-ROM drive, refer to your system documentation for performing a

Network Installation Management (NIM) installation.

3. Type the following command at the System Management Interface Tool (SMIT) fast path:

smit

devinst

Press Enter. The Install Additional Device Software window appears with INPUT device / directory

for software option highlighted.

4. Type the name of the input device that you are using, or press F4 to select the input device from a

list.
Press Enter. The Install Additional Device Software window is shown with the

SOFTWARE to

install

option highlighted.

5. Press F4 to select List.
6. Type

to display the Find window.

7. Type the device package name, and press Enter.

The device driver software is shown.

8. Press F7 to select the highlighted device driver software, and press Enter.

The Install Additional Device Software window is displayed. The entry fields are automatically

updated.
Press Enter twice to confirm. The Command Status window is displayed.
• The message

RUNNING

is highlighted to indicate that the installation and configuration command is

in progress.

• When

RUNNING

changes to

, scroll to the bottom of the page and locate the installation

summary.

• After a successful installation,

SUCCESS

is displayed in the

Result

column of the installation

summary at the bottom of the page.

9. Remove the installation media from the drive.

10. Press F10 to exit SMIT.
11. To verify that the device drives is installed, complete the following steps:

a) If necessary, log in as root user.

b) At the command line, type

lslpp -l devices.xxxxxxxxxx

where xxxxxxxxxx is the device

package name.
Press Enter.
The following example shows when the adapter device driver is installed.

File set

Level

State

Description

Path: /usr/lib/objrepos

devices.xxxxxxxxxx

5.3.8.0

COMMITTED Adapter name software

Verify that the file sets are installed at the AIX version level you are running. Level 5.3.8.0 is an

example. If no data is displayed on your screen, the adapter device driver was not installed

correctly. Try reinstalling the driver.

32 Power Systems: PCIe adapters for the 9080-M9S

Summary of Contents for FC EJ05



































































Search results

Summary of Contents for FC EJ05

Reviews:

Related manuals for FC EJ05

Brands by name

Popular brands

IBM FC EJ05, Manual

Search results

Summary of Contents for FC EJ05

Reviews:

Related manuals for FC EJ05

Brands by name

Popular brands