g.
The disk unit that you installed should appear in the list. The serial
number should match the serial number you wrote in step 13 on page
48.
Note:
If the disk unit does not appear in the list, ensure that you
properly installed the disk unit.
h.
Return to the Work with Disk Units menu (Press F12 three times).
__ 32.
On the
Work with disk units
display, select
Work with disk configuration.
Press the Enter key.
__ 33.
Are you adding a disk unit to an existing device parity set? If you need
more information about device parity, go to the book,
Backup and Recovery
,
SC41-5304-04 .
Yes
No
↓
Go to step 52 on page 53.
__ 34.
On the
Work with Disk Configuration
display, select
Work with device parity
protection
.
__ 35.
On the
Work with Device Parity Protection
display, select
Include unit in device
parity protection
.
__ 36.
Did the
Include Device Parity Protection Failed
display appear?
Yes
No
↓
Go to step 39.
__ 37.
You must meet the following conditions before you can start device parity
protection. Including the disk unit in device parity protection may fail for
one or more reasons.
v
If there are enough disk units available to create a new parity set, the
units will be eligible for
Start Device Parity Protection
operation. The disk
units will not be eligible for the
Include Device Parity Protection
operation.
For more information, go to the
Backup and Recovery
, SC41-5304-04 .
v
All disk units in a parity set must be the same capacity. The resulting
parity set must have a minimum number of 4 disk units and
maximum of 10 units.
v
Not all disk units attached to an advanced function input/output
processor have reported to the system. Retry the operation.
v
The type/model of the disk units is not supported for the requested
operation.
__ 38.
When you have met the above conditions, select F12 to return to the
Work
with disk configuration
display.
__ 39.
On the
Include Disk Units in Device Parity Protection
display, select the disk
units to be included in Device Parity Protection by typing a
1
in the
Option
column.
Press the Enter key.
__ 40.
Press Enter to confirm your choice.
__ 41.
When the device parity protection is complete, the message “Selected
unit(s) have been included successfully” appears on the
Work with device
parity protection
display.
Press F12.
__ 42.
On the
Work with disk configuration
display, select
Display disk configuration.
Press the Enter key.
52
Setting Up Your 5065 or 5066 Expansion Unit V4R5
Summary of Contents for AS/400e
