IBM 7379E2U, Installation And User Manual

Page: 22 / 152

Features and specifications
The following information is a summary of the features and specifications of the
server. Depending on the server model, some features might not be available, or
some specifications might not apply.
Table 1. Features and specifications
Microprocessor:
v Intel
®
Xeon
®
up to six-core with
integrated memory controller and Quick
Path Interconnect (QPI) architecture
v Designed for LGA 1366 socket
v Scalable up to twelve cores
v 32 KB instruction cache, 32 KB data
cache, and 4MB, 8 MB and 12MB
cache that is shared among the cores
v Support for up to two microprocessors,
second microprocessor with pluggable
VRM
v Support for Intel Extended Memory 64
Technology (EM64T)
Note:
v
Use the Setup utility to determine the
type and speed of the microprocessors.
For a list of supported microprocessors,
see http://www.ibm.com/servers/eserver/
serverproven/compat/us/
v Do not install an Intel Xeon
™
5500
series microprocessor and an Xeon
™
5600 series microprocessor in the same
server.
.
Memory:
v Sixteen DIMM connectors (eight per
microprocessor)
v Minimum: 1 GB
Note: If you install a
ServeRAID-M1015 SAS/SATA adapter,
make sure at least 2 GB of memory is
installed in the server before you run
DSA from a bootable CD.
v Maximum: 128 GB
– 48 GB using unbuffered DIMMs
(UDIMMs)
– 128 GB using registered DIMMs
(RDIMMs)
v
Type: Registered or unbuffered ECC
double-data-rate 3 (DDR3) 800, 1066,
and 1333 MHz DIMMs only
v
RDIMMs sizes: 1 GB, 2 GB , 4 GB ,
and 8 GB single-rank or dual-rank
v
UDIMMs sizes: 1 GB, 2 GB, and 4 GB
single-rank or dual-rank
v
Chipkill supported
Drives:
v SATA:
–
DVD (standard)
– DVD/CD-RW (optional)
– Maximum of two devices can be
installed
v
Diskette (optional): External USB 1.44
MB
v
Supported hard disk drives:
– Serial Attached SCSI (SAS)
Expansion bays:
v Sixteen 2.5-inch HDD bays (three
optical DVD drive bays)
v Four 3.5-inch simple-swap SATA
drives
v Eight 3.5-inch HDD bays (one
UltraSlim DVD drive)
v Three half-high 5.25-inch bays (one
DVD drive installed)
Note:
– SAS expander card does not
support 3 GB RAID adapters.
– Full-high devices such as an
optional tape drive will occupy two
half-high
5.25-inch bays.
– If the server is configured for RAID
operation using a ServeRAID
adapter, you might have to
reconfigure your disk arrays after
you install drives. See the
ServeRAID adapter documentation
for additional information about
RAID operation and complete
instructions for using the
ServeRAID adapter.
PCI and PCI-X expansion slots:
v Six PCI expansion slots on the system
board:
– Four PCI Express x8 (2x8 link, 2x4
link)
– One PCI Express x16 (x8 link)
– One PCI 32-bit
v One or two expansion slots on the PCI
extender card:
– Standard - One PCI Express x8 (x4
link) on the PCI-Express extender
card
– Optional - Two PCI-X 64/133 slots on
the PCI-X extender card
Hot-swap fans:
v Three (standard)
Note: To upgrade to redundant cooling,
install the redundant power and cooling
option kit. The kit includes one 920-watt
hot-swap power-supply and three hot-swap
fans.
Size:
v
Tower
– Height: 440 mm (17.3 in.)
– Depth: 767 mm (30.2 in.)
– Width: 218 mm (8.6 in.)
– Weight: approximately 37.85 kg (83.4
lb) when fully configured or 27.1 kg
(59.7 lb) minimum
v Rack
– 5 U
– Height: 218 mm (8.6 in.)
– Depth: 702 mm (27.6 in.)
– Width: 424 mm (16.7 in.)
– Weight: approximately 36 kg (79.3 lb)
when fully configured or 25.8 kg (56.9
lb) minimum
Racks are marked in vertical increments of
4.45 cm (1.75 inches). Each increment is
referred to as a unit, or “U.” A 1-U-high
device is 4.45 cm (1.75 inches) tall.
Power supply:
v
Standard: One 670 watt (100 - 240 V
AC)
Note: On models with eight 3 5-inch or
ServeRAID SAS adapter:
v ServeRAID-BR10i SAS/SATA adapter
that supports RAID levels 0, 1, 1E
(standard)
Humidity:
v
Server on: 20% to 80%, maximum dew
point 21°C, maximum rate of change
5°C/hour
S
ff
6
IBM System x3400 M3 Type 7378/7379: Installation and User's Guide