+-----------+------------------------------------+-----------+-----------¦
¦ ¦ ¦ ¦ D = 50% ¦
¦ CD ¦ Illegal Operation Code ¦ 2 ¦ ¦
¦ ¦ ¦ ¦ S = 50% ¦
+-----------+------------------------------------+-----------+-----------¦
¦ ¦ Invalid field or reserved bits set ¦ ¦ D = 50% ¦
¦ CE ¦ in CDB ¦ 2 ¦ ¦
¦ ¦ ¦ ¦ S = 50% ¦
+-----------+------------------------------------+-----------+-----------¦
¦ ¦ ¦ ¦ D = 50% ¦
¦ CF ¦ This LUN is not supported ¦ 2 ¦ ¦
¦ ¦ ¦ ¦ S = 50% ¦
+-----------+------------------------------------+-----------+-----------¦
¦ ¦ Invalid field in Parameter List ¦ ¦ D = 50% ¦
¦ D0 ¦ (Mode Data) ¦ 2 ¦ ¦
¦ ¦ ¦ ¦ S = 50% ¦
+-----------+------------------------------------+-----------+-----------¦
¦ ¦ Illegal bit set in identify ¦ ¦ D = 50% ¦
¦ D1 ¦ message ¦ 2 ¦ ¦
¦ ¦ ¦ ¦ S = 50% ¦
+-----------+------------------------------------+-----------+-----------¦
¦ ¦ ¦ ¦ D = 50% ¦
¦ D2 ¦ Media removal is prevented ¦ 2 ¦ ¦
¦ ¦ ¦ ¦ S = 50% ¦
+-----------+------------------------------------+-----------+-----------¦
¦ ¦ Command has mode mismatch ¦ ¦ D = 50% ¦
¦ D3 ¦ (variable/fixed) ¦ 2 ¦ ¦
¦ ¦ ¦ ¦ S = 50% ¦
+-----------+------------------------------------+-----------+-----------¦
¦ ¦ ¦ ¦ D = 50% ¦
¦ D4 ¦ Illegal Transfer Length in CDB ¦ 2 ¦ ¦
¦ ¦ ¦ ¦ S = 50% ¦
+-----------+------------------------------------+-----------+-----------¦
¦ ¦ Tried to change Mode Parms and not ¦ ¦ D = 50% ¦
¦ D6 ¦ at LBOT ¦ 2 ¦ ¦
¦ ¦ ¦ ¦ S = 50% ¦
+-----------+------------------------------------+-----------+-----------¦
¦ ¦ Can't read medium incompatible ¦ ¦ D = 50% ¦
¦ D7 ¦ format ¦ 14 ¦ ¦
¦ ¦ ¦ ¦ S = 50% ¦
+-----------+------------------------------------+-----------+-----------¦
¦ ¦ Overlapped commands attempted bad ¦ ¦ D = 50% ¦
¦ D8 ¦ ITL nexus ¦ 2 ¦ ¦
¦ ¦ ¦ ¦ S = 50% ¦
+-----------+------------------------------------+-----------+-----------¦
¦ ¦ ¦ ¦ D = 50% ¦
¦ DA ¦ Illegal bits set in ID message ¦ 2 ¦ ¦
¦ ¦ ¦ ¦ S = 50% ¦
+-----------+------------------------------------+-----------+-----------¦
¦ DB ¦ Cannot write to tape not AME ¦ 10 ¦ I ¦
+-----------+------------------------------------+-----------+-----------¦
¦ DC ¦ Rounding has occurred ¦ 7 ¦ I ¦
+-----------+------------------------------------+-----------+-----------¦
¦ ¦ ¦ ¦ D = 50% ¦
¦ DD ¦ Not ready -- head sync tape ¦ 2 ¦ ¦
¦ ¦ ¦ ¦ S = 50% ¦
+-----------+------------------------------------+-----------+-----------¦
¦ ¦ ¦ ¦ D = 50% ¦
¦ DE ¦ Density not supported ¦ 2 ¦ ¦
¦ ¦ ¦ ¦ S = 50% ¦
+-----------+------------------------------------+-----------+-----------¦
¦ E0 ¦ Aborted in CDB phase, parity or ¦ 12 ¦ B = 100% ¦
¦ ¦ other error ¦ ¦ ¦
+-----------+------------------------------------+-----------+-----------¦
¦ E1 ¦ Aborted prior to Data phase, bad ¦ 12 ¦ B = 100% ¦
¦ ¦ message ¦ ¦ ¦
+-----------+------------------------------------+-----------+-----------¦
¦ E2 ¦ Aborted in Data phase, init ¦ 12 ¦ B = 100% ¦
¦ ¦ detected error ¦ ¦ ¦
+-----------+------------------------------------+-----------+-----------¦
¦ E3 ¦ Aborted in Data phase, bad message ¦ 12 ¦ B = 100% ¦
+-----------+------------------------------------+-----------+-----------¦
¦ E4 ¦ Aborted after Data phase, bad ¦ 12 ¦ B = 100% ¦
¦ ¦ message ¦ ¦ ¦
+-----------+------------------------------------+-----------+-----------¦
¦ E5 ¦ Aborted after Data phase, other ¦ 12 ¦ B = 100% ¦
¦ ¦ error ¦ ¦ ¦
+-----------+------------------------------------+-----------+-----------¦
¦ E6 ¦ ABORT caused by SCSI Bus Parity ¦ 12 ¦ B = 100% ¦
¦ ¦ Error ¦ ¦ ¦
+-----------+------------------------------------+-----------+-----------¦
¦ E7 ¦ ABORT sent by initiator has been ¦ 12 ¦ B = 100% ¦
¦ ¦ completed ¦ ¦ ¦
+-----------+------------------------------------+-----------+-----------¦
7208 Tape Drive Setup and Operator Guide
Appendix B. Fault Symptom Codes and Error Recovery Procedure Numbers
¦ Copyright IBM Corp. 1998
B.0 - 5
