IAI AP-3200T-PMCL User Manual Download

Page: 45 / 76

—

AP-3200T-

PMCL

Shield the camera sensor.

If a lens is attached, use the lens cap as a shield, for example.

Configure the threshold level for defective pixel detection.

Up to 200 pixels can be corrected for each of the three sensors.
The threshold value is specified as a percentage.
The default setting is "10" with 10% of the full scale (100%) specified as the threshold

value.

Execute [BlemishDetect] to start automatic detection.

After detection, the interpolation data is saved to the camera's internal memory.

To check the number of interpolated pixels after automatic detection

You can check the number of pixels interpolated via automatic detection by loading the

BlemishNum data.

■

Manual configuration

Select the index in [BlemishCompensationIndex].

You can select from 1 to 200. However, configure the indexes in order starting with the smallest

index. If you skip indexes while configuring settings, interpolation may not be performed.

Specify the pixel points for interpolation using the

[BlemishCompensationPositionX] and [BlemishCompensationPositionY] settings.

You can configure values that are within the total effective pixel area. Specify pixels for which

interpolation is not necessary as -1. If 0 is specified, the first line or first pixel will be interpolated.

Note

BlemishCompensationDataClear[specify sensor][BlemishCompensationIndex], you can return a

specific pixel correction setting to the default value (storage not required).

Execute [BlemishStore].

Blemish compensation data will be stored.

Set [BlemishEnable] to [True], and execute interpolation.

If it is set to [False] , Blemish compensation is not effective.

ShadingCorrection

The ShadingCorrection function corrects non-uniformity (i.e., shading) in the amount of light

generated by the lens and lighting equipment. Using this function allows correction even if top,

bottom, left, and right shading is not symmetrical in relation to the center of the screen (H, V).

This function can be used even when the effective image area is limited (an area with both

Width and Height set to more than 128 must must be configured) by the ROI function. In

such cases, the correction area is included in the image area configured by the ROI.

For a full image, the number of correction blocks is 17 (H) × 13 (V) blocks and calculation

errors in the correction data are minimized due to the small interpolation areas. Each block is

128 × 128 pixels. The total size of the blocks is 2176 (H) × 1664 (V), but the actual number

of effective pixels for the camera is 2064 (H) × 1554 (V). The ineffective peripheral areas will

be deleted internally on the camera automatically.

Summary of Contents for AP-3200T-PMCL













































































Search results

Summary of Contents for AP-3200T-PMCL

Reviews:

Related manuals for AP-3200T-PMCL

Brands by name

Popular brands

IAI AP-3200T-PMCL, User Manual

Search results

Summary of Contents for AP-3200T-PMCL

Reviews:

Related manuals for AP-3200T-PMCL

Brands by name

Popular brands