Genuine Accessories
Electronic Installation Instructions
Glasses
Gloves
Mask
Hearing Protection
Part Weight (Gross)
FMVSS 110 Compliance Information
Part Weight (Net)
1) Read the entire Installation Instructions prior to beginning the installation of the part.
2)
3) Make sure the vehicle is completely clean and dry in the area(s) the part is to be installed.
4) Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed.
5) NEVER place tools on painted surfaces, seating surfaces, dash pad, console or floor carpet/mats.
6) Always wear appropriate personal protective equipment, including gloves, safety glasses, etc., when required.
7) Record radio presets prior to disconnecting battery, if needed.
8) Roll down the driver's window and adjust the power seats (if applicable) prior to disconnecting battery power, if needed.
9)
10)
10mm Socket
Basic Required Tools
Denotes cautions to be taken to avoid
vehicle and component damage
(B) Dealer Technician
Denotes warnings that may lead to
serious physical injury or vehicle damage
Denotes quality processes to be checked
prior to moving to the next step
Denotes personal protective equipment (PPEs) that
may be required for a step. Examples of safety
equipment icons noted below:
Ratchet
Extension
Pliers
12mm Socket
T20 Torx Socket
#2 Phillips
Screwdriver
Entered by
MPA
Tape Measure
T20 Torx Driver
Nylon Panel
Removal Tool
Torque Wrench
Side Cutters
N
O
T
E
Denotes important information to be
reviewed during the step
(C) Master Technician or Specialist
If this is a printed copy of the installation instructions, ensure you have the latest revision by
scanning the QR code or by entering the website address listed below before beginning
installation. Use the latest revision date as noted by “Rev. Date” above.
www.hyundaiaccessories.com/admin_media_uploads/installationSheets/l0f62_au000.pdf
Instructional Symbols / Definitions
Denotes cautions to be taken to avoid
physical injury or electronic component
damage
Denotes specific tools that are necessary
to complete a step
Copy OEM Logo Here (
→
)
Vehicle Model: Sonata
Accessory: Mirror, Auto-Dimming w/ HL5
Model Year
2020~
Difficulty:
( B )
Part No.
L0F62 AU000 (DIO)
L0F62 AU600 (PIO)
Note:
Difficulty stated above reflects the minimum level of
expertise required to install the accessory:
Language
English
Rev. Date
3/3/2020
(A) Customer
10mm Deep Well
Socket
10mm Combination
Wrench
1.10
lbs
Universal Joint
Ensure the parking brake is set and foot is on the brake pedal while function checking.
All dealers must determine if the Net weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed
options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a “Load
Carrying Capacity Reduced” label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced carrying
capacity in kilograms or pounds, which is the total weight of all added options and accessories.
Load Label Part Number: NP070 - 09003
0.50
kg
0.75
lbs
0.34
kg
Notes to the installer:
Factory wire harness colors are subject to change. Please use the specified pin number in the harness connector to identify
the correct wire for T-Tap installation.
If applicable, scan the barcode label located on the accessory part or packaging prior to installing, to register the part. If this accessory is installed as
a replacement, register the removal of the old part before registering the new part. Old and new parts will have different barcode data, and the old
registration cannot be reused.
T20
M12
T20
M10
M10
M10
Revision Date
03/03/2020
Page 1 of 16
