FLOW
(FLUJO)
DRIVE SECTION
(SECCION MOTRIZ)
ADJUST TO DESIRED ELEVATION
(AJUSTE A LA ALTURA DESEADA)
DRIVE
(UNIDAD MOTRIZ)
END DIVERTER
(DESVIADOR DEL EXTREMO)
END DIVERTER
(DESVIADOR DEL EXTREMO)
TAIL SECTION
(SECCION DE RETORNO)
INTERMEDIATE SECTION
(SECCION INTERMEDIA)
DIVERT SECTION
(SECCION DE DESVIACIÓN)
INTERMEDIATE DIVERTER
(DESVIADOR-INTERMEDIO)
"MATCH-MARK" NUMBERS
(ETIQUETAS DE SECUENCIA DE ARMADO)
MARK
CONVEYOR F.0.#
ITEM TO
HYTROL CONVEYOR CO. INC.
JONESBORO, AR
A
1
2
12345
MARK
CONVEYOR F.0.#
ITEM TO
HYTROL CONVEYOR CO. INC.
JONESBORO, AR
A
1
2
12345
NOTE: ALLOW FOR BELT THICKNESS WHEN ADJUSTING SUPPORTS
(NOTA: DEJE ESPACIO SUFICIENTE PARA EL ESPESOR DE LA BANDA CUANDO AJUSTE LOS SOPORTES)
INSTALLATION
• Support Installation
1. determine primary direction of product flow. Figure 4A indicates the preferred flow as related to the drive.
2. Refer to “match-mark” numbers on ends of conveyor sections. (Figure 4A) Position them in this sequence near the area of installation.
3. Attach supports to both ends of drive section and to one end of intermediate or tail sections (Figure 4A). Hand tighten bolts only at this time. Conveyors
angle of incline will determine where the knee brace mounting brackets are to be placed when required.
4. Adjust elevation to required height.
FIGURE 4A
• Conveyor Set-Up
1. mark a chalk line on floor to locate the center of the conveyor.
2. Place the drive section in position.
3. Install remaining sections. Check the “match-mark” numbers to see that adjoin-
ing sections are in proper sequence (Figure 4A). It is important that each bed
section be checked for a “racked” or out-of-square condition. If conveyor is not
square, tracking problems will result. Figure 4C indicates a racked section.
TO CORRECT AN OUT-OF-SQUARE SECTION
3a. Locate points on corners of section and measure distance “A” & “B”. If the
dimensions are not equal, the section will need to be squared. (Figure 4d).
3b. Use crossbracing (where supplied) to square individual sections. Adjust turn-
buckle until dimensions “A” & “B” are equal.
4. Fasten sections together with splice plates and support spacers (Figure 4B).
5. Check to see that the conveyor is level across the width and length of the unit.
Adjust the supports as necessary and lag to floor.
6. Install electrical controls and wire motor. See Page 5.
7. Install and track belt per instructions on Pages 5, 6 &7.
(WHEN SUPPLIED)
RETURN IDLER
SUPPORT SPACER CHANNEL
CONVEYOR SIDE CHANNEL
PIVOT PLATE
STATIONARY SUPPORT
SPLICE PLATE
(PLACA DE EMPALME)
(SOPORTE DEL CANAL ESPACIADOR)
(RODILLO DE ALINEACIÓN)
BED SPACER
(ESPACIADOR
DE CAMA)
(PLACA PIVOTE)
(SOPORTE ESTACIONARIO)
(CANAL LATERAL DEL TRANSPORTADOR)
ImPORTANT! Being out of level across width of conveyor can cause package
drift on long conveyor lines.
SIDE CHANNEL
(CANAL LATERAL)
ROLLERS NOT SQUARE WITH SIDE CHANNELS
(LOS RODILLOS NO ESTAN ESCUADRADOS CON LOS CANALES)
“Racked” conveyor sections will cause package to travel toward side of conveyor.
"A"
"B"
SIDE CHANNEL
(CANAL LATERAL)
(SHORT ROD)
(VARILLA CORTA)
FRAME SPACER
(ESPACIADOR DE CAMA)
TURNBUCKLE
(TENSOR)
SIDE CHANNEL
(CANAL LATERAL)
(LONG ROD) CROSSBRACING
([VARILLA LARGA] TIRANTE TENSOR)
FIGURE 4B
FIGURE 4C
FIGURE 4D
4
Summary of Contents for ProSort SC1
Page 35: ...35...
