HYOSUNG COMET 650 FI Owner'S Manual Download Page 72

Page: 72 / 90

◉

FRONT BRAKE LAMP SWITCH

The front brake lamp switch is located

beneath the front brake lever. Loosen the
switch fitting screws and adjust the timing by
moving the switch body forward or back-
ward.

◉

REAL BRAKE LAMP SWITCH

The rear brake lamp switch is located at

right-side of the engine.

Move the switch up or down to adjust it

until the switch operates and turns on the
brake lamp after the brake pedal begins to
be depressed.

◉

REAR BRAKE FLUID SUPPLY

1. Place the motorcycle on a level surface

and keep the handlebars straight.

2. Clean the brake fluid reservior around not

to allow dust to get inside of it.

3. Turn the cap to the counter - clockwise.
4. Replenish with brake fluid to the upper

line.

N O T E

The recommended brake fluid : DOT4

5. Fasten the cap.

Do not spill any brake fluid on painted or
plastic surfaces as it will damage the
surface severely.

CAUTION

◉

BRAKE DISK INSPECTION.

Check the brake disk for damage or cracks.

◉

FRONT BRAKE FLUID SUPPLY

1. Place the motorcycle on a level surface

and keep the handlebars straight.

2. Clean the brake fluid reservior around not

to allow dust to get inside of it.

3. Loosen the screw and open the cap.
4. Replenish with brake fluid to the upper

line.

N O T E

The recommended brake fluid : DOT4

5. Fasten the cap.

Comet650 2008.7.11 3:40 PM ˘

` 71 JINSUN 300DPI 100LPI T

Summary of Contents for COMET 650 FI



























































































Search results

Summary of Contents for COMET 650 FI

Reviews:

Brands by name

Popular brands

HYOSUNG COMET 650 FI, Owner'S Manual

Search results

Summary of Contents for COMET 650 FI

Reviews:

Brands by name

Popular brands