background image

© Copyright 2004 Hydrotech, Inc. 

Form No.  OGRO-1230H-03 03.04

Part No. 36101265

 

LIMITED WARRANTY

 

 

Subject to the conditions and limitations described below, HYDROTECH, Inc. warrants its Model 12301, 12302, and 12304 
Series Reverse Osmosis Drinking Water Treatment Systems (excluding cartridge filters and battery), when installed in 
accordance with HYDROTECH, Inc. specifications, to be free from defects in materials and workmanship under normal use 
within the operating specifications for a period of two (2) years from the date of purchase.  HYDROTECH, Inc. also warrants the 
Smartap

®

 Water Quality Monitor to be free from defects in materials and workmanship under normal use within the operating 

specifications for a period of five (5) years from the date of purchase.  This warranty shall apply to the original end-user of the 
system only. 
 
Other than the cartridge filters and battery, any part found defective within the terms of this warranty will be repaired or replaced 
by HYDROTECH, Inc.   If any part is found defective, HYDROTECH, Inc. also reserves the right to replace the drinking water 
appliance with a comparable HYDROTECH, Inc. drinking water system of equal or greater quality.  You pay only freight for 
repaired or replaced parts from our factory and local dealer charges, including but not limited to labor charges, travel and 
transportation expenses and handling fees. 
 
This warranty shall not apply to any part damaged by accident, fire, flood, freezing, Act of God, bacterial attack, membrane 
fouling and/or scaling, sediment, misuse, misapplication, neglect, alteration, installation, or operation contrary to our printed 
instructions, or by the use of accessories or components which do not meet HYDROTECH, Inc. specifications.  If the drinking 
water system is altered by anyone other than HYDROTECH, Inc. the warranty shall be void. 
 
ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR 
PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THE PERIOD SPECIFIED ABOVE FOR THE PARTS 
DESCRIBED IN THIS LIMITED WARRANTY. 
 
As a manufacturer, we do not know the characteristics of your water supply.  The quality of water supplies may vary 
seasonably or over a period of time.  Your water usage may vary as well.  Water characteristics can also change if the drinking 
water appliance is moved to a new location.  For these reasons, we assume no liability for the determination of the proper 
equipment necessary to meet your requirements, and we do not authorize others to assume such obligation for us.  Further, 
we assume no liability and extend no warranties, express or implied, for the use of this product with a non-potable water source 
or a water source which does not meet the conditions for use as described in this Owners Guide. 
 
HYDROTECH’S OBLIGATIONS UNDER THIS WARRANTY ARE LIMITED TO THE REPAIR OR REPLACEMENT OF THE 
FAILED PARTS OF THE DRINKING WATER SYSTEM, AND WE ASSUME NO LIABILITY WHATSOEVER FOR DIRECT, 
INDIRECT, INCIDENTAL, CONSEQUENTIAL, SPECIAL, GENERAL OR OTHER DAMAGES, WHETHER FROM CORROSION 
OR OTHER CAUSES. 
 
Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. 

 Similarly, some states do not allow the exclusion of incidental or consequential damage, so the above limitation or 

exclusion may not apply to you.  This warranty gives you specific legal rights, and you may have other rights that vary 

from state to state.

 

 

For warranty return or information, please contact the Water Professional who installed your unit.

 

Your Unit was installed by:

 

 

 

Summary of Contents for SERIES 12301





















Reviews: