ii
ROUTINE MAINTENANCE
It is important that any water treatment system be properly maintained to ensure consistent water quality. The information provided on this
page is of a general nature. See Cleaning, Disinfecting, and Routine Maintenance Procedure on Page 18 and 19 for detailed information.
Refer to Mounting Bracket and System Plumbing Installation Instructions on Page 1, and the appropriate System Assembly and Activation
Procedures for detailed information to install your specific UV system.
Cleaning:
The inside of the system and the quartz sleeve should be
cleaned each time the filters are changed. Clean all parts (except
the filters and electronic parts) with soap and rinse them thoroughly
with clean potable water. Dry the inside of the quartz sleeve
thoroughly before re-assembling system.
NOTE:
Presence of iron or general poor water quality will
require frequent inspection and cleaning.
“O” Rings:
Lubricate each “O” ring with a silicone based “O” ring
lubricant to ensure a proper seal.
NOTE:
UV lamp should remain on at all times during use
because; repeated starting of UV lamp shortens lamp
life, and UV lamp requires a warm up period of 1-2
minutes.
Replacement: Filters will normally last approximately four to six
months. Filter life will vary due to water conditions. A reduced flow
rate or deteriorating water quality indicates that filters must be
changed.
Use only UV filters. UV filters are specially designed to work in
the ultraviolet disinfection process. Use of non-UV filters voids the
warranty.
CAUTION:
Use care when changing the filters to avoid breaking
the quartz sleeve.
UV Lamp Replacement: Lamps must be changed every twelve
months. While UV lamps rarely burn out, they do lose their
disinfection power. Use only UV UV lamps as they are specifically
designed for the UV system to deliver high quality drinking water.
UV ULTRAVIOLET SPECIFICATIONS
Model
Shipping
Weight
lbs. (kg)
Dimensions◊
Inches (Centimeters)
Height x Width x Depth
Flow Rate
Gallons Per Minute
Liters per Minute
Lamp Type &
Power Used
Watts
Inlet/ Outlet
UVB1
10.0 lbs. (4.5 kg)
15.0” x 5.5” x 5.5”
(38.1 cm x 14.0 cm x 14.0 cm)
2 gpm (7.6 L/min)
UV Lamp #11
14 Watts
3/8” NPT
†
UVB2
15.0 lbs. (6.8 kg)
15.0” x 11.0” x 5.5”
(38.1 cm x 27.9 cm x 14.0 cm)
UVB3
24.0 lbs. (10.9 kg)
15.0” x 16.0” x 5.5”
(38.1 cm x 40.6 cm x 14.0 cm)
UV20-1
16.0 lbs. (7.3 kg)
25.0” x 5.5” x 5.5”
(63.5 cm x 14.0 cm x 14.0 cm)
10 gpm (38 L/min)
UV Lamp #20
22 Watts
3/4” NPT
†
UV20-2
24.0 lbs. (10.9 kg)
25.0” x 11.0” x 5.5”
(63.5 cm x 27.9 cm x 14.0 cm)
UV20-3
32.0 lbs. (14.5 kg)
25.0” x 16.0” x 5.5”
(63.5 cm x 40.6 cm x 14.0 cm)
8 gpm (30 L/min)
UVBB-1
20.0 lbs. (9.1 kg)
29.5” x 7.5” x 9.0”
(74.9 cm x 19.0 cm x 22.9 cm)
15 gpm (57 L/min)
UV Lamp #20
22 Watts
1-1/2” NPT
†
UVBB-2
35.0 lbs. (15.9 kg)
28.0” x 15.0” x 9.0”
(71.1 cm x 38.1 cm x 22.9 cm)
UVBB-3
53 lbs. (24.0 kg)
28.0” x 23.0” x 9.0”
(71.1 cm x 58.4 cm x 22.9 cm)
UV1
7.0 lbs. (3.2 kg)
13.5” x 5.0” x 5.0”
(34.3 cm x 12.7 cm x 12.7 cm)
1 gpm (3.8 L/min)
UV Lamp #10
10 Watts
1/2” NPT
†
UV A/O-1
5.0 lbs. (2.3 kg)
12.0” x 4.0” x 3.5”
(30.5 cm x 10.2 cm x 8.9 cm)
1 gpm (3.8 L/min)
UV Lamp #10
10 Watts
3/8 QC
‡
UV A/O-3
7.0 lbs. (3.2 kg)
22.5” x 4.0” x 3.5”
(57.2 cm x 10.2 cm x 8.9 cm)
3 gpm (11.4 L/min)
UV Lamp #20
22 Watts
† Female thread as recognized by United Sates National Pipe Thread.
‡ Push-in Quick Connectors or Quick Connectors (QC).
◊ All dimensions of system do not include inlet/outlet piping connections and are rounded up to the nearest 1/2”.
Summary of Contents for Aqua Flo ADDON Series
Page 2: ......
