manualshive.com logo in svg

Hydac 3.6.4 FCM 100-K Series, Operating And Maintenance Instructions Manual, Page: 45 / 88

Share
Download
Hydac 3.6.4 FCM 100-K Series Operating And Maintenance Instructions Manual Download Page 45

HYDAC FILTER SYSTEMS GMBH

Setting up / assembly / integration of the filter unit | 5

BeWa FCM 3160267e en-us lq

45 / 88

5.4 Making the electrical connections

Depending on the version, the filter unit has different drive mo-
tors (different voltage / output / number of phases, etc.). Follow
the instructions in the next section to electrically connect the fil-
ter unit.

5.4.1 Connecting the filter unit with a single-phase

electric motor

For the version with a single-phase electric motor, the filtration
unit is supplied ready for connection with a plug.

1.

Remove the connector cable from its holder and unwind

it completely.

2.

Before plugging in the power plug, make sure that the

on/off switch is in the 0 or OFF position.

3.

Check that the voltage and frequency are correct. You

will find the filter unit's electrical data on the electric mo-

tor's name plate.

4.

Plug the power plug into a suitable power outlet.

5.

Switch the filter unit on or off using the switch on the mo-

tor terminal box.

Depending on the version, the filter unit has ther-
mal protection in the motor windings and a motor
protection switch in the junction box to protect it
from electrical overload.

Summary of Contents for 3.6.4 FCM 100-K Series

























































































Reviews:

No comments