manualshive.com logo in svg

Hydac 3.6.4 FCM 100-K Series, Operating And Maintenance Instructions Manual, Page: 43 / 88

Share
Download
Hydac 3.6.4 FCM 100-K Series Operating And Maintenance Instructions Manual Download Page 43

HYDAC FILTER SYSTEMS GMBH

Setting up / assembly / integration of the filter unit | 5

BeWa FCM 3160267e en-us lq

43 / 88

5.2 Measure or display dynamic pressure / differential

pressure

If pressure is measured in a hydraulic system, the type of mea-
surement such as dynamic pressure  or differential pressure 
as well as the measurement point is critical, as shown in the
following diagram.

Fig. 12: 

Measure or display dynamic pressure / differential pressure

∑p = Total of the pressures

∆p1 = Differential pressure

p1 = Back-pressure

∆p2 = Differential pressure

p2 = Back-pressure

∆p3 = Differential pressure

p3 = Back-pressure

∆p4 = Differential pressure

p4 = Back-pressure

In the example, the dynamic pressure at the first measurement
point shows the total of the following pressures in the hydraulic
system.

Summary of Contents for 3.6.4 FCM 100-K Series

























































































Reviews:

No comments