HWH 700 Series Service Manual Download Page 4

Page: 4 / 39

C:\TEMP\ml59101.doc | Revised: 20JUN18 | Page 4 of 39

CONTROL IDENTIFICATION

"EMERGENCY STOP" BUTTON

"EXCESS SLOPE"

"NOT IN PARK"

RAISE RIGHT SIDE BUTTON

LOWER RIGHT SIDE BUTTON

LEVELING LIGHTS
(4 - Yellow)

WARNING LIGHTS
(4 - Red)

RAISE REAR BUTTON

LOWER REAR BUTTON

"AIR" (ON) BUTTON

DUMP LIGHT

"TRAVEL MODE" BUTTON

"TRAVEL MODE"

LEVELING SYSTEM

"DUMP" BUTTON

RAISE LEFT SIDE

BUTTON

LOWER LEFT SIDE
BUTTON

RAISE FRONT BUTTON

LOWER FRONT BUTTON

LIGHT

CAUTION!

HWH COMPUTERIZED LEVELING

UNDERSTAND OPERATOR'S MANUAL BEFORE USING. BLOCK FRAME AND TIRES

SECURELY BEFORE REMOVING TIRES OR CRAWLING UNDER VEHICLE.

NOT IN
PARK /

BRAKE

DUMP

RAISE

EMERGENCY

STOP

AIR

TRAVEL

EXCESS

SLOPE

RAISE LIGHT

"RAISE" BUTTON

"TRAVEL MODE" BUTTON

LIGHT (Red)

HARD RESET SWITCH
(SEE HWH LIGHTED RESET SWITCH)

MASTER WARNING LIGHT

ACTIVE LIGHT

LIGHT (Green)

MODE

CONTROL FUNCTIONS

CONTROL BUTTONS

INDICATOR LIGHTS

“AIR” BUTTON:

This is the system active and

automatic operation button. It woks if the ignition is in
the “ON” position.

“EMERGENCY STOP” BUTTON:

This button turns

the system OFF but does NOT control power to the
“DUMP” or “RAISE” buttons. Pushing this button will
NOT put the system in the TRAVEL mode.

“TRAVEL MODE” BUTTON:

This button will put the

Leveling system in the TRAVEL mode. The ignition
must be “ON” for the vehicle to return to proper ride
height for traveling.

“DUMP” BUTTON:

This button will lower the whole

coach by dumping air from the suspension system.

“RAISE” BUTTON:

This button will raise the whole

coach by adding air to the suspension system.

IMPORTANT:

Read “DUMP AND RAISE

FUNCTIONS” before using the “DUMP” and “RAISE”
buttons.

UP ARROWS (RAISE BUTTONS):

These

momentary buttons are used for manually operating
the air leveling systems. Sides or ends of the vehicle
will raise while these buttons are pushed.

DOWN BUTTONS (LOWER BUTTONS):

These

momentary buttons are used for manually operating
the air leveling systems. Sides or ends of the vehicle
will lower while these buttons are pushed.

LEVEL SYSTEM ACTIVE LIGHT:

Flashes during automatic

leveling and sleep mode.

DUMP LIGHT:

Flashes when “DUMP” button is pushed.

RAISE LIGHT:

Flashes when “RAISE” button is pushed.

“EXCESS SLOPE” LIGHT:

ON if the leveling system can NOT

level the coach.

“TRAVEL MODE” BUTTON LIGHT (RED):

Light flashes for 3

seconds after the “TRAVEL MODE” button is pushed.

TRAVEL MODE LIGHT (GREEN):

ON if the ignition is in the

“ON” position, the system is not being used, and there is
sufficient air pressure in the suspension.

WARNING LIGHTS:

Function with the ignition in the “ON”

position. ON when the LEVELING SYSTEM ACTIVE LIGHT
flashing.

LEVELING LIGHTS:

One or two yellow lights can be on

indicating the side, end or corner of the coach is low.

“NOT IN PARK/BRAKE” LIGHT:

ON while the “AIR” button is

being pushed if the Park Brake is NOT set. The light will go out
when the “AIR” button is released.

MASTER WARNING LIGHT:

ON any time the “TRAVEL” light is

not ON, if the ignition is in the ON position.

Summary of Contents for 700 Series








































Search results

Summary of Contents for 700 Series

Reviews:

Brands by name

Popular brands

HWH 700 Series, Service Manual

Search results

Summary of Contents for 700 Series

Reviews:

Brands by name

Popular brands