Husqvarna HS 139A Workshop Manual Download Page 28 | Manualshive

Page: 28 / 48

background image

3. Remove the governor rod (A) from the governor arm

(B).

A

B

4. Remove the governor spring from the governor

control and the governor arm.

5. Loosen the governor arm nut and remove the

governor arm bolt.

6. Remove the governor arm.
7. Remove the governor control.
8. Replace all worn and damaged parts.
9. Install in the opposite sequence.
10. Adjust the governor. Refer to

To adjust the governor

on page 29.

6.5.9 To remove and install the governor

1. Remove the air filter. Refer to

To remove and install

the air filter on page 20.

2. Disconnect the governor rod from the governor

shaft.
a) Rotate the governor rod 90 degrees in the

governor shaft.

b) Lift and remove the governor rod.

3. Remove the governor rod (A) from the governor arm

(B).

A

B

4. Remove the governor spring from the governor

control and the governor arm.

5. Loosen the governor arm nut and remove the

governor arm bolt.

6. Remove the governor arm.
7. Remove the governor bolt and the washer.
8. Remove the governor control.
9. Replace all worn and damaged parts.
10. Install in the opposite sequence.
11. Adjust the governor. Refer to

To adjust the governor

on page 29.

28 - Repair instructions

1425 - 001 - 03.06.2020

«
...
26
27
28
29
30
...
»

Summary of Contents for HS 139A

















































Reviews:

No comments

Related manuals for HS 139A

Brand: VAR-SPE Pages: 80

Brand: Hägglunds Pages: 56

Brand: Saab Pages: 30

Vanguard 540000 Series

Brand: Briggs & Stratton Pages: 32

Brand: Engine distributors Pages: 331

44 A FOUR-35C THREE

Brand: Westerbeke Pages: 61

Brand: Danfoss Pages: 77

Brand: Champion Power Equipment Pages: 29

PowerLine TG500B

Brand: Texas Pages: 98

Brand: ZF Pages: 80

Brand: Stafer Pages: 6

IntelliGear Plus

Brand: Browning Pages: 20

Brand: STG-BEIKIRCH Pages: 25

Brand: Volvo Pages: 20

Brand: Volvo Pages: 51

Brand: Volvo Pages: 76

Brand: MULTIPLEX modell Pages: 11

Brand: LONCIN Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands