Husqvarna HS 139A Workshop Manual Download Page 20 | Manualshive

Page: 20 / 48

background image

6.3 Air filter

6.3.1 To remove and install the air filter

WARNING: Use protective gloves.

1. Push the clips on the air filter cover.
2. Carefully remove the air filter cover (A) from the

engine.

3. Remove the air filter (B).

A

B

4. Examine the air filter for damages. Replace a

damaged air filter.

5. Clean and examine the air filter. Refer to

the paper filter on page 20.

6. Install in the opposite sequence.

6.3.2 To clean the paper filter

1. Remove the air filter cover and remove the paper

filter.

2. Hit the filter against a flat surface to make the

particles fall off.

CAUTION: Do not use solvent or

compressed air to clean the paper filter.

3. Put the air filter back. Make sure that the air filter

fully seals against the air filter holder.

4. Put the air filter cover back.

6.3.3 To remove and install the air filter holder

WARNING: Use protective gloves.

1. Remove the air filter. Refer to

To remove and install

the air filter on page 20.

2. Remove the 2 nuts and remove the air filter holder.

3. Install in the opposite sequence.

20 - Repair instructions

1425 - 001 - 03.06.2020

«
...
18
19
20
21
22
...
»

Summary of Contents for HS 139A

















































Reviews:

No comments

Related manuals for HS 139A

Brand: Canaline Engines Pages: 39

Brand: Grundfos Pages: 25

Brand: Petter Pages: 58

Brand: DJ ENGINE Pages: 9

RolloTube S-line DuoFern

Brand: RADEMACHER Pages: 8

RolloTube Basis

Brand: RADEMACHER Pages: 60

Brand: RADEMACHER Pages: 64

DYNAMIC LINE III

Brand: KEB Pages: 60

Brand: Mitsubishi Pages: 522

Brand: Seva-tec Pages: 20

Brand: DANA Pages: 4

Brand: Honda Pages: 96

Brand: Honda Pages: 114

Car Engine GX340

Brand: Honda Pages: 96

Brand: Mitsubishi Heavy Industries Pages: 200

Brand: LIMBACH Pages: 48

Brand: LIMBACH Pages: 53

Brand: SKY Engines Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands