Husqvarna 966613301 Operator'S Manual Download | Manualshive

Page: 23 / 68

background image

ContRols

23

Cutting Height Pedal

The cutting height pedal lifts the deck to allow setting
the desired deck height. For transport, push the lift
pedal fully forward until the deck lift latches in the
transport (highest) position.

8065-087

Cut height lift pedal

8065-085

Choke control

Choke Control

The choke control is used for cold starts to provide
the engine with a richer fuel mixture.
For cold starts the control should be pulled out to its
extent.

Fuses

Fuses are located on the right hand side of the
machine. They are accessed by tilting the seat
forward. Fuses are flat pin fuses type as used in
automobiles.
There are three fuses with ratings and functions:

20 A, Primary fuse.

1.

7.5 A, Mower deck coupling.

2.

10 A, Accessories

3.

8065-043

Fuses

«
...
21
22
23
24
25
...
»

Summary of Contents for 966613301





































































Reviews:

No comments

Related manuals for 966613301

Brand: Yard Machines Pages: 12

Brand: AL-KO Pages: 652

Brand: Yazoo Pages: 24

Brand: Racing Pages: 29

Brand: MTD Pages: 29

Brand: McCulloch Pages: 100

Brand: Toro Pages: 12

Brand: Yazoo/Kees Pages: 72

Brand: Yard Machines Pages: 28

Brand: Snapper Pages: 224

Brand: Craftsman Pages: 68

Brand: Electrolux Pages: 20

Brand: Electrolux Pages: 6

Brand: Craftsman Pages: 28

Brand: Craftsman Pages: 30

Brand: Craftsman Pages: 56

Brand: Craftsman Pages: 56

Brand: Craftsman Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands