Husqvarna 966613301 Operator'S Manual Download | Manualshive

Page: 35 / 68

background image

1

2

oPeRatIon

35

Manual Transport

8058-091

1. Release lever locked into the bypass position
2. Release lever, engaged

Right side, ZT-3400 linkage

When pushing or pulling the mower, engage the
bypass linkages with the hydro release levers. The
levers are located on each side of the rear of the unit
below the engine plate.
Raise the deck to the highest (transport) position.
Pull the bypass linkages up and out of the keyhole
slots. Release the lever with the head outside the
bracket and held into the bypass setting.
To reengage the hydro to drive, reverse the above
procedure.

WARNING!
No adjustments or maintenance
should be carried out unless:

the engine stopped

•

the ignition key removed

•

the parking brake activated

•

«
...
33
34
35
36
37
...
»

Summary of Contents for 966613301





































































Reviews:

No comments

Related manuals for 966613301

Brand: Baroness Pages: 325

32in Recycler 30118

Brand: Toro Pages: 4

Brand: Alamo Pages: 168

Craftsman 917.250262

Brand: Sears Pages: 60

Brand: Grasshopper Pages: 56

Brand: Sabo Pages: 124

Brand: MTD Pages: 28

Brand: Toro Pages: 28

Brand: Worldlawn Pages: 14

Brand: Toro Pages: 28

Brand: MTD Pages: 18

23HP Z-Force 60

Brand: Cub Cadet Pages: 32

Brand: VITO GARDEN Pages: 24

Brand: Toro Pages: 28

Giant-Mow M4815KAWV

Brand: Giant-Vac Pages: 36

Brand: Kellfri Pages: 28

Brand: EINHELL Pages: 208

shindaiwa SBA-LE24

Brand: Yamabiko Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands