Husqvarna 966613301 Operator'S Manual Download | Manualshive

Page: 19 / 68

background image

ContRols

19

Motion Control Levers

The machine’s speed and direction are continuously
variable using the two steering controls. The steering
controls can be moved forward or backward about
a neutral position. Furthermore, there is a neutral
position, which is locked if the steering controls are
moved outward.
When both controls are in the neutral position (N), the
machine stands still.
By moving both controls an equal amount forward
or backward, the machine moves in a straight line
forward or backward respectively.
For example, to turn right while moving forward, move
the right control towards the neutral position. The
rotation of the right wheel is reduced and the machine
turns to the right.
Zero turn can be achieved by moving one control
backward (behind the neutral position) and carefully
moving the other steering control forward from its
neutral position. The rotation direction when zero
turning is determined by which steering control is
moved backward behind the neutral position. If the left
steering control is pulled backward, the machine turns
to the left. Use extra care when using this maneuver.

8065-053

1. Forward
2. Neutral
3. Neutral slot, Neutral lock
4. Reverse

Motion control lever pattern (right side)

WARNING!
The machine can turn very rapidly if
one steering control is moved much
further forward than the other.

8065-003

Steering controls

«
...
17
18
19
20
21
...
»

Summary of Contents for 966613301





































































Reviews:

No comments

Related manuals for 966613301

Brand: Land Pride Pages: 4

Brand: Land Pride Pages: 3

Accu-Z Razor Z48

Brand: Land Pride Pages: 62

Brand: Yard-Man Pages: 24

Greens King V Plus

Brand: Jacobsen Pages: 224

Brand: Texas Pages: 16

Brand: elem Pages: 99

Brand: Sabo Pages: 92

Brand: Elem Garden Technic Pages: 32

Garden Mark ZYJ-197A

Brand: Montgomery Ward Pages: 12

Brand: Yard-Man Pages: 12

Brand: Jacobsen Pages: 106

Brand: Bad Boy Pages: 34

Brand: LawnMaster Pages: 26

Brand: Craftsman Pages: 40

Brand: Craftsman Pages: 31

Brand: Craftsman Pages: 32

Brand: Craftsman Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands