Husqvarna 966613301 Operator'S Manual Download | Manualshive

Page: 31 / 68

background image

oPeRatIon

31

Running

Release the parking brake by moving the lever

1.

downward.
NOTE: The mower is equipped with an operator
presence system. When the engine is running,
any attempt by the operator to leave the seat
without first setting the parking brake will shut off
the engine.
Move the steering controls to the neutral position

2.

(N).

The cutting height can be set from 1"- 5½"

3.

(2.5 cm-14 cm) by setting the cutting height pin
into the desired hole. Release deck height control
by pushing forward on the pedal.

Set pin at desired cutting height. (Pin is removed

4.

by rotating 180

O

.) Push pedal again to lower deck

to selected setting.

8065-006

Release the parking brake

8065-087

Deck lift pedals

8065-090

Set deck to selected cutting height

«
...
29
30
31
32
33
...
»

Summary of Contents for 966613301





































































Reviews:

No comments

Related manuals for 966613301

Brand: Yard-Man Pages: 36

Brand: Yard force Pages: 45

Brand: Ransomes Pages: 36

Brand: McCulloch Pages: 20

Brand: LawnBoss Pages: 34

Brand: Roller Derby Pages: 4

Brand: Gianni Ferrari Pages: 96

Brand: Viking Pages: 284

Brand: MDL POWERUP Pages: 26

Brand: Ozito Pages: 14

Brand: Dixie Chopper Pages: 124

Brand: Bushranger Pages: 20

Brand: Weed Eater Pages: 4

Brand: Weed Eater Pages: 24

Brand: Weed Eater Pages: 48

Brand: Poulan Pro Pages: 48

Brand: Poulan Pro Pages: 30

Brand: Poulan Pro Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands