11. Air filter cover
12. Throttle trigger
13. Handle adjustment
14. Cutting attachment guard
15. Drive disc
16. Grease filler cap
17. Choke control
18. Air purge bulb
19. Combination wrench
20. Hex key
21. Locking pin
22. Operators manual
Symbols on the product
WARNING! This product is dangerous.
Injury or death can occur to the operator or
bystanders if the product is not used
carefully and correctly. To prevent injury to
the operator or bystanders, read and obey
all safety instructions in the operator's
manual.
Please read the operator's manual carefully
and make sure that you understand the
instructions before use.
Use a protective helmet in locations where
objects can fall on you. Use approved
hearing protection. Use approved eye
protection.
Use approved protective gloves.
Use heavy-duty slip-resistant boots.
The product can cause objects to eject,
which can cause injury.
Maximum speed of the output shaft.
50FT
15 m
50FT
15 m
Keep a minimum of 15 m distance to
persons and animals during operation of the
product.
Only use flexible cutting wire. Do not use
metal cutting elements.
The arrows shows the limit for the handle
position.
Air purge bulb.
Choke.
Refuelling.
Noise emission to the environment refer to
the European Community's Directive. The
emission of the product is specified in the
Technical data chapter and on the label.
The product agrees with the applicable EC
directives.
The rating plate shows the
serial number. yyyy is the
production year, ww is the
production week and xxxx
is the sequential number.
yyyywwxxxx
Note: Other symbols/decals on the product refer to
certification requirements for other commercial areas.
EU V
WARNING: Tampering with the engine voids
the EU type-approval of this product.
Product liability
As referred to in the product liability laws, we are not
liable for damages that our product causes if:
• the product is incorrectly repaired.
• the product is repaired with parts that are not from
the manufacturer or not approved by the
manufacturer.
• the product has an accessory that is not from the
manufacturer or not approved by the manufacturer.
• the product is not repaired at an approved service
center or by an approved authority.
1003 - 001 - 07.01.2019
3
Summary of Contents for 525 LX
