Husqvarna 520iHE3 Workshop Manual Download Page 50

Page: 50 / 59

50 – English

Symptom

Possible causes

Recommended action

The product cannot be activated. No
LEDs come on after pressing the on/
off button.

Faulty battery

1. Check the battery by pressing the

status button. At least one green
LED should light up. See also Bat-
tery and Charger

Bad contact between battery and
product.

2. Make sure the power connectors

between the battery and the prod-
uct are not dirty or damaged. See
illustration in annex.

Damage to the multi-wire cable
between the control unit and the
keypad or main switch.

3. Repair or change the multi-wire

cable. (Applies only if there is vis-
ible damage.)

Short circuit in control unit

4. Replace the control unit

The product cannot be activated
and batteries that are inserted are
immediately ruined.

Short circuit in control unit

Replace the control unit

The electric motor does not react
after pressing the control.

Poor connection in main switch
signal contact.

1. Make sure the main switch signal

connector is correctly assembled,
dry, is not damaged and is
corrosion-free. See illustration in
annex.

Motor contacts not properly as-
sembled.

2. Make sure the motor contact/mo-

tor contacts are correctly fitted.
See figure

5 in the annex

Interior damage to main switch

3. Replace the main switch

Short circuit in control unit

4. Replace the control unit

Electric motor stutters for a short
period when pressing the control,
after which it stops.

Short circuit in control unit

Replace the control unit

The product turns off under load

Bad contact between battery and
product.

Make sure the power connectors
between the battery and the product
are not dirty or damaged. See illus-
tration in annex.

Short circuit in keypad

Replace the cabling.

Uneven motor speed

Poor connection in main switch
signal contact.

1. Make sure the main switch signal

connector is correctly assembled,
dry, is not damaged and is
corrosion-free. See figure 3 in the
appendix

Damaged or worn out main switch

2. Replace the main switch

10 Troubleshooting - 536LiHE3

Summary of Contents for 520iHE3




























































Search results

Summary of Contents for 520iHE3

Reviews:

Related manuals for 520iHE3

Brands by name

Popular brands

Husqvarna 520iHE3, Workshop Manual

Search results

Summary of Contents for 520iHE3

Reviews:

Related manuals for 520iHE3

Brands by name

Popular brands