Husqvarna 520iHE3 Workshop Manual Download Page 17 | Manualshive

Page: 17 / 59

background image

English – 17

Diagnosis and troubleshooting

6 Diagnosis and Troubleshooting

6.1 Remove the battery

Press in the catches and remove the battery.

.

WARNING!

Do not short circuit the battery!

Never unscrew the battery!

Never fit a damaged battery!

Replace a damaged battery!

6.2 Connect the diagnostic tool

1

NB! Ensure that the cutting unit is in working

position when the tests in the Common service

tool are being performed.

Connect the adapter cable for the diagnostic tool

to the battery and the battery contact on the pole

hedge trimmer.

Connect cable (A) to the diagnostic tool for trouble-

shooting the pole hedge trimmer.

Connect cable (B) to the diagnostic tool for trouble-

shooting the battery.

NB! Refer to the manual for the Diagnostic Tool

Battery for detailed instructions and follow the

instructions in the diagnostic tool.

2

Diagnose/troubleshoot according to the diagnostic

tool instructions and make any necessary repairs

as instructed in the relevant chapter in this manual.

6.3 No signal to diagnostic tool

1

Check that the contact on the battery and the bat-

tery contact on the product are intact and clean.

Replace the battery or control unit respectively on

the pole hedge trimmer if there is any damage.

2

Check that the cable to the diagnostic tool is intact

and clean. Replace the cable if it is damaged.

3

Restart the computer/Reinstall the software.

2

1

1

A

B

«
...
15
16
17
18
19
...
»

Summary of Contents for 520iHE3




























































Reviews:

No comments

Related manuals for 520iHE3

Brand: Gardena Pages: 9

Brand: Think ahead Pages: 2

sunjoe TRJ13STE

Brand: SNOWJOE Pages: 56

CONNECTED MAX CMACC-SWD-12-WH

Brand: CREE LIGHTING Pages: 6

Brand: Black+Decker Pages: 124

Home Easy HE-107

Brand: Byron Pages: 2

Brand: Nakayama Pages: 29

Brand: Makita Pages: 92

Brand: Craftsman Pages: 25

Brand: Craftsman Pages: 32

Brand: Craftsman Pages: 14

Brand: Craftsman Pages: 8

Brand: Craftsman Pages: 8

257.798051 Important

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 6

Brand: Craftsman Pages: 19

Brand: Craftsman Pages: 8

Brand: Craftsman Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands