Husqvarna 2016 FE 250 Owner'S Manual Download Page 67

Page: 67 / 124

12 SERVICE WORK ON THE CHASSIS

12.41

Checking the frame

401799-01

–

Check the frame for cracks and deformation.
» If the frame exhibits cracks or deformation due to a mechanical impact:

–

Change the frame.

Info

Always replace a frame that has been damaged due to a mechan-

ical impact. Repair of the frame is not authorized by Husqvarna

Motorcycles.

12.42

Checking the swingarm

401520-01

–

Check the swingarm for damage, cracking, and deformation.
» If the swingarm shows signs of damage, cracking, or deformation:

–

Change the swingarm.

Info

Always change a damaged swingarm. Repair of the swingarm is

not authorized by Husqvarna Motorcycles.

12.43

Checking the routing of the throttle cable

Preparatory work

–

Remove the seat. (

p. 49)

–

Remove the fuel tank.

(

p. 59)

H00252-01

Main work

–

Check the routing of the throttle cable.

Both throttle cables must be routed to the throttle valve body side by side

behind the handlebars and above the fuel tank bearing.

» If the throttle cable is not routed as specified:

–

Correct the routing of the throttle cable.

Finishing work

–

Install the fuel tank.

(

p. 60)

–

Mount the seat. (

p. 50)

Summary of Contents for 2016 FE 250





























































































































Search results

Summary of Contents for 2016 FE 250

Reviews:

Related manuals for 2016 FE 250

Brands by name

Popular brands

Husqvarna 2016 FE 250, Owner'S Manual

Search results

Summary of Contents for 2016 FE 250

Reviews:

Related manuals for 2016 FE 250

Brands by name

Popular brands