Husqvarna 2016 FE 250 Owner'S Manual Download Page 63

Page: 63 / 124

12 SERVICE WORK ON THE CHASSIS

H00188-11

(FE EU/AU)

–

Position the collar bushings and horn, and mount and tighten screws



Guideline

Remaining screws, chassis

10 Nm (7.4 lbf ft)

–

Connect the connector of the horn.

S00906-11

(FE US)

–

Position the collar bushings, and mount and tighten screws



Guideline

Remaining screws, chassis

10 Nm (7.4 lbf ft)

H00248-10

–

Plug in connector



for the fuel pump.

–

Remove the wash cap set.

–

Thoroughly clean the plug-in connection of the fuel line using compressed air.

Info

Under no circumstances should dirt enter into the fuel line. Dirt in the fuel

line clogs the injection valve!

–

Lubricate the O-ring and connect plug-in connection



for the fuel line.

Info

Route the cable and fuel line at a safe distance from the exhaust system.

Finishing work

–

Mount the seat. (

p. 50)

12.36

Checking for chain dirt accumulation

400678-01

–

Check the chain for coarse dirt accumulation.
» If the chain is very dirty:

–

Clean the chain. (

p. 61)

12.37

Cleaning the chain

Warning

Danger of accidents

Oil or grease on the tires reduces their grip.

–

Remove oil and grease with a suitable cleaning material.

Warning

Danger of accidents

Reduced braking efficiency due to oil or grease on the brake discs.

–

Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Summary of Contents for 2016 FE 250





























































































































Search results

Summary of Contents for 2016 FE 250

Reviews:

Related manuals for 2016 FE 250

Brands by name

Popular brands

Husqvarna 2016 FE 250, Owner'S Manual

Search results

Summary of Contents for 2016 FE 250

Reviews:

Related manuals for 2016 FE 250

Brands by name

Popular brands