Husqvarna 2016 FE 250 Owner'S Manual Download Page 111

Page: 111 / 124

23 TECHNICAL DATA

109

23.3

Capacities

23.3.1

Engine oil

Engine oil

1.0 l (1.1 qt.)

Engine oil (SAE 10W/50) (

p. 113)

23.3.2

Coolant

Coolant

1.2 l (1.3 qt.)

Coolant (

p. 113)

23.3.3

Fuel

Total fuel tank capacity,

approx. (FE EU/AU)

9.5 l (2.51 US gal)

Super unleaded (ROZ 95/RON 95/PON 91) (

p. 113)

Total fuel tank capacity,

approx. (FE US)

8.5 l (2.25 US gal)

Super unleaded (ROZ 95/RON 95/PON 91) (

p. 113)

Fuel reserve, approx.

1.5 l (1.6 qt.)

23.4

Chassis

Frame

Central tube frame made of chrome molybdenum steel tubing

Fork

WP Performance Systems

Up Side Down 4860 MXMA 4CS

Suspension travel

Front

300 mm (11.81 in)

Suspension travel

Rear

330 mm (12.99 in)

Fork offset

22 mm (0.87 in)

Shock absorber

WP Performance Systems

5018 DCC

Brake system

Disc brakes, brake calipers on floating bearings

Brake discs - diameter

Front

260 mm (10.24 in)

Rear

220 mm (8.66 in)

Brake discs - wear limit

Front

2.5 mm (0.098 in)

Rear

3.5 mm (0.138 in)

Tire air pressure off road

Front

1.0 bar (15 psi)

Rear

1.0 bar (15 psi)

Road tire pressure (FE EU/AU)

Front

1.5 bar (22 psi)

Rear

1.5 bar (22 psi)

Final drive (FE EU/AU)

14:52 (13:52)

Final drive (FE US)

13:52

Chain

5/8 x 1/4"

Rear sprockets available

48, 50, 52

Steering head angle

63.5°

Wheelbase

1,482±10 mm (58.35±0.39 in)

Seat height unloaded

970 mm (38.19 in)

Ground clearance unloaded

345 mm (13.58 in)

Homologated weight without fuel, approx. (FE EU/AU)

109.3 kg (241 lb.)

Weight without fuel, approx. (FE US)

107.3 kg (236.6 lb.)

Maximum permissible front axle load

145 kg (320 lb.)

Maximum permissible rear axle load

190 kg (419 lb.)

Maximum permissible overall weight

335 kg (739 lb.)

Summary of Contents for 2016 FE 250





























































































































Search results

Summary of Contents for 2016 FE 250

Reviews:

Related manuals for 2016 FE 250

Brands by name

Popular brands

Husqvarna 2016 FE 250, Owner'S Manual

Search results

Summary of Contents for 2016 FE 250

Reviews:

Related manuals for 2016 FE 250

Brands by name

Popular brands