Hurricane BLO-VAC 36 Operator'S Manual Download Page 49 | Manualshive

Page: 49 / 53

background image

TROUBLESHOOTING

Troubleshooting Chart

Hydraulics

Machine will not move with
engine running

• Parking brake engaged.
• Transmission oil level low.
• Transmission oil cold.
Allow machine to warm up.
• Pump drive belt slipping or broken.
• Pump free-wheel valves open.
• Transmission problems.
See your authorized service center.

Machine creeps with engine
running and motion control
levers in a neutral position

• Needs motion control linkage
neutral center adjustment.

Machine

Excessive machine vibration

• Engine speed too slow.
Increase engine rpms.
• Drive belt not tensioned correctly.
• Impeller out of balance.
Check impeller for damage, cracks,
broken or bent fins. If damaged in
any way, REPLACE IMPELLER.

Discharge deflectors not
opening or closing

• Deflector switch broken or
sticking, replace switch.
See your authorized service center.
• Deflector breaker bad, replace.
See your authorized service center.
• Deflector motor damaged.
See your authorized service center.

46

«
...
47
48
49
50
51
...
»

Summary of Contents for BLO-VAC 36






















































Reviews:

No comments

Related manuals for BLO-VAC 36

Brand: Lawn-Boy Pages: 16

Brand: Solo Pages: 92

Brand: Little Wonder Pages: 54

Pro Attachment ES-210

Brand: Echo Pages: 32

Brand: Murray Pages: 44

Brand: Promaker Pages: 24

Brand: Monster Power Equipment Pages: 22

Brand: Craftsman Pages: 80

Brand: Craftsman Pages: 72

Brand: Craftsman Pages: 72

Brand: Craftsman Pages: 32

Brand: Craftsman Pages: 64

Brand: Craftsman Pages: 47

Brand: Craftsman Pages: 64

Brand: Craftsman Pages: 56

Brand: Craftsman Pages: 76

247.88173 series

Brand: Craftsman Pages: 68

Brand: Craftsman Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands