background image

 

44 

 

3.4.4. Notification 

 

REMOTE NOTIFY

   

The system can notify an event to the IP address of Remote Software PC over the network.

 

Select REMOTE NOTIFY to use this function and set IP address & events. 
 

ADD/EDIT/DELECT 

User can use these to add/edit/delete IP address of Remote Software PC. 

 
IP ADDRESS 

Input the IP address of Remote Software PC which will receive events notification. 
 

PORT 

Input Port number which is set at the Remote Software PC. Default is 8003. 
 

EVENT 

Select events to be notified. When “ALL” is selected, all of the events will be notified.. 
 

     

 

 

Note 

Configuration first priority is always on “SCHEDULE” of “RECORD”. 
Thus, the system will not notify alarm upon motion alarm or sensor even though user ticks 

the check-box of above event selection, unless user sets the “SCHEDULE” of “RECORD” 
and “MOTION”/”SENSOR” of “DEVICE” accordingly. 

For example, if user sets just “Continuous” only in “SCHEUDLE” of “RECORD” and tick “All” 

check-box of “REMOTE NOTIFY”, the system will not notify alarm message.    In this case, 
user has to set “CONT + MOT”, “MOTION”, “SENSOR” or “CON + SENS” to enable 
REMOTE NOTIFY properly. 

 

Note 

User can set remote pop-up in RemoteManager S/W (RMS) and Central Management S/W 

(CMS) upon alarm trigger in NVR. 

In order for RMS or CMS user to receive an instant pop-up video over network from NVR, 

NVR user has to tick “SENSOR” or “MOTION ALARM” in above menu. 

“SENSOR” means the alarm triggered by physical alarm, while “MOTION ALARM” means 

the alarm triggered by motion detection. 

 

Note 

In order to receive event notification properly, event port in the setting menu of the Remote 

Software PC should be the same to that of in this setting screen. 

 

Note 

In case the Remote software PC is not in the same network with NVR, port forwarding for 

the PC should be required to receive remote notify properly. 

 
 
E-MAIL NOTIFY 

The system can make an event notification to the e-mail address registered in the NVR. 
Select E-MAIL NOTIFY to use this function and set e-mail address & events. 

 
ADD/EDIT/DELECT 

User can use these to add/edit/delete e-mail address. 
 

E-MAIL 

Summary of Contents for HNR-3016GN


























































Reviews: