Hughes 9211 User Manual Download Page 61 | Manualshive

Page: 61 / 80

background image



Using the Web UI

3500988-0001 Revision A

53

Usage Page

This web page provides an estimate of the amount of Packet
Switched data that was sent and received, along with time spent
on streaming connections and CS calls. The data is broken up
into two types:

Trip Usage Statistics:

The trip counter is similar to the trip

counter on your vehicle. It can be zeroed out at any time by the
user and it will track the statistics until the user resets it.

Lifetime Usage Statistics:

The Lifetime counter is similar to

the odometer on your vehicle. It shows the statistics of the
terminal since the software version that added this feature was
loaded onto the UT. The user

cannot

reset these counters.

If the UT power is abruptly disconnected for some reason, the
UT will not be able to save the statistics to flash and hence the
statistics for the session (

Trip

) may be inaccurate.

«
...
59
60
61
62
63
...
»

Summary of Contents for 9211

















































































Reviews:

No comments

Related manuals for 9211

Brand: H3C Pages: 7

Brand: Maco Antennas Pages: 9

Brand: M2 Antenna Systems Pages: 5

Brand: EchoStar Pages: 28

Brand: M2 Antenna Systems Pages: 7

airMAX airGrid M5HP

Brand: Ubiquiti Pages: 28

Brand: Ebyte Pages: 6

Brand: Ubiquiti Pages: 20

Brand: Apex Digital Pages: 4

Brand: M2 Antenna Systems Pages: 8

Brand: AEG Pages: 10

ANT2407 - PROSAFE Indoor 7 dBi Omni-directional Antenna

Brand: NETGEAR Pages: 2

Brand: NETGEAR Pages: 35

Brand: Scout Pages: 2

Yagi Y200 Series

Brand: ZCG Pages: 2

Brand: ZCG Pages: 2

Brand: ZCG Pages: 2

ANT806 - ANT 806 - TV Antenna

Brand: RCA Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands