Huawei Telecom Power TP48200A-HT19C3 User Manual Download Page 96

Page: 96 / 99

TP48200A-HT19C3 and TP48200A-HT19C4 Telecom
Power
User Manual

C Associations Between Alarms and Dry Contacts on the

UIM

Issue 03 (2019-11-15)

Associations Between Alarms and Dry

Contacts on the UIM

Table C-1

Associations between alarms and dry contacts

Port Type

Silk Screen

Associated Alarm

Dry contact input

DIN1

Dry contact input 1

DIN2

Dry contact input 2

DIN3

Dry contact input 3

DIN4

Dry contact input 4

DIN5

Dry contact input 5

DIN6

TEC Alarm

Dry contact output

The default setting (closed:
alarm; open: normal) can be
modified.

ALM1

Mains faults

ALM2

DC overvoltage and undervoltage

ALM3

Rectifier faults

ALM4

AC surge protective device (SPD) faults or DC SPD faults

ALM5

Battery or load fuse blown

ALM6

Excessively high or low ambient and battery temperatures

ALM7

Door status alarm

ALM8

Fan faults

Summary of Contents for Telecom Power TP48200A-HT19C3




































































































Search results

Summary of Contents for Telecom Power TP48200A-HT19C3

Reviews:

Related manuals for Telecom Power TP48200A-HT19C3

Brands by name

Popular brands

Huawei Telecom Power TP48200A-HT19C3, User Manual

Search results

Summary of Contents for Telecom Power TP48200A-HT19C3

Reviews:

Related manuals for Telecom Power TP48200A-HT19C3

Brands by name

Popular brands