Huawei Telecom Power TP48200A-HT19C3 User Manual Download Page 70

Page: 70 / 99

TP48200A-HT19C3 and TP48200A-HT19C4 Telecom
Power
User Manual

4 Maintenance

Issue 03 (2019-11-15)

Follow-up Procedure

Pack the removed component and return it to the local Huawei warehouse.

4.4.6 Replacing the Internal Circulation Fan of the Heat Exchanger

Prerequisites



Prepare an ESD wrist strap, a pair of ESD gloves, an ESD box or bag, the cabinet door
key, and a maintenance tool kit.



Check that the new fan is intact.

Procedure

Step 1

Disconnect the power cable from the UIM02C.

Connect the ground cable to the ESD wrist strap, and wear the ESD wrist strap and ESD
gloves.

Record the position where the UIM02C panel connects to the signal cable, and then
disconnect the signal cable.

Unscrew the UIM02C, as shown in Figure 4-8.

Disconnect the -48 V power cable from the UIM02C backplane, as shown in Figure 4-9.

Step 2

Disconnect the transfer terminal from the internal circulation fan.

Step 3

Removing the internal circulation fan.

Record the position where cables connect to the internal circulation fan, and then
disconnect the cables.

Remove the cover from the internal circulation fan, as shown in Figure 4-11.

Figure 4-11

Removing the cover from the internal circulation fan

Remove the fan fixing plate from the internal circulation fan, as shown in Figure 4-12.

Summary of Contents for Telecom Power TP48200A-HT19C3




































































































Search results

Summary of Contents for Telecom Power TP48200A-HT19C3

Reviews:

Related manuals for Telecom Power TP48200A-HT19C3

Brands by name

Popular brands

Huawei Telecom Power TP48200A-HT19C3, User Manual

Search results

Summary of Contents for Telecom Power TP48200A-HT19C3

Reviews:

Related manuals for Telecom Power TP48200A-HT19C3

Brands by name

Popular brands