Huawei SUN2000-55KTL User Manual Download Page 120

Page: 120 / 122

SUN2000-(55KTL, 60KTL) Series
User Manual

B Grid Codes

Issue 06 (2020-01-03)

114

No.

Grid Code

Description

Nicaragua-MV800

Nicaragua power grid

Ghana-MV800

Ghana medium-voltage power grid

Table B-5

lists the grid codes that the SUN2000-60KTL-HV-D1-001 supports.

Table B-5

Grid codes (for the SUN2000-60KTL-HV-D1-001)

No.

Grid Code

Description

G59-England-MV800

G59 medium-voltage power grid

AS4777-MV800

Australia medium-voltage power grid

IEC61727-MV800

IEC61727 medium-voltage power grid

BDEW-MV800

Germany medium-voltage power grid

ABNT NBR 16149-MV800

Brazil medium-voltage power grid

UTE C 15-712-1-MV800

France power grid

Chile-MV800

Chile power grid

Mexico-MV800

Mexico power grid

EN50438-TR-MV800

Turkey power grid

TAI-PEA-MV800

Thailand power grid

Philippines-MV800

Philippines power grid

Malaysian-MV800

Malaysia power grid

NRS-097-2-1-MV800

South Africa power grid

DUBAI-MV800

Dubai power grid

EN50438_IE-MV800

Ireland power grid

CLC/TS50549-MV800

Ireland power grid

Northern Ireland-MV800

Northern Ireland power grid

CEI0-21-MV800

Italy power grid

IEC 61727-MV800-60Hz

General

BRASIL-ANEEL-MV800

Brazil power grid

CEI0-16-MV800

Italy medium-voltage power grid

ARGENTINA-MV800

Argentina medium-voltage power grid

JAMAICA-MV800

Jamaica medium-voltage power grid

VDE-AR-N4120_HV800

VDE4120 standard power grid

Summary of Contents for SUN2000-55KTL



























































































































Search results

Summary of Contents for SUN2000-55KTL

Reviews:

Related manuals for SUN2000-55KTL

Brands by name

Popular brands

Huawei SUN2000-55KTL, User Manual

Search results

Summary of Contents for SUN2000-55KTL

Reviews:

Related manuals for SUN2000-55KTL

Brands by name

Popular brands