Huawei SUN2000-43KTL-IN-C1 User Manual Download Page 65

Page: 65 / 99

SUN2000-43KTL-IN-C1
User Manual

5 Connecting Cables

Issue 07 (2018-05-06)

Table 5-4

Functions of the RS485 terminal block

No.

Port Definition

Description

RS485A IN

RS485A, RS485 differential

RS485A OUT

RS485A, RS485 differential

RS485B IN

RS485B, RS485 differential signal –

RS485B OUT

RS485B, RS485 differential signal –

Connecting Cables to the Terminal Block

Step 1

Remove an appropriate length of the jacket and core wire insulation layer from the
communications cable using a wire stripper.

Figure 5-25

Stripping an RS485 communications cable

Step 2

Remove the locking caps from the COM1 and COM2 waterproof cable connectors at the
SUN2000 bottom and remove the plugs from the locking caps.

Step 3

Route the communications cable through the locking caps, and then the COM1 (RS485 IN)
and COM2 (RS485 OUT) connectors at the SUN2000 bottom.

Step 4

Remove the terminal base from the terminal block.

Step 5

Connect communications cables to the terminal base.

Figure 5-26

Connecting cables to a terminal base

(1) RS485A IN

(2) RS485A OUT

(3) RS485B IN

(4) RS485B OUT

Summary of Contents for SUN2000-43KTL-IN-C1




































































































Search results

Summary of Contents for SUN2000-43KTL-IN-C1

Reviews:

Brands by name

Popular brands

Huawei SUN2000-43KTL-IN-C1, User Manual

Search results

Summary of Contents for SUN2000-43KTL-IN-C1

Reviews:

Brands by name

Popular brands