Huawei SUN2000-43KTL-IN-C1 User Manual Download Page 15

Page: 15 / 99

SUN2000-43KTL-IN-C1
User Manual

2 Overview

Issue 07 (2018-05-06)

No.

Component

Silk Screen

Waterproof cable connector (inner
diameter: 18–44 mm)

AC OUTPUT 1

Waterproof cable connector (inner
diameter: 24–32 mm)

AC OUTPUT 2

USB port

USB

DC switch 1

DC SWITCH 1

DC switch 2

DC SWITCH 2

Waterproof cable connector (inner
diameter: 14–18 mm)

COM1, COM2, COM3

DC input terminals (controlled by
DC SWITCH 1)

+/–

DC input terminals (controlled by
DC SWITCH 2)

+/–



Waterproof cable connector is abbreviated as waterproof connector in the following text.



Use the USB port only during maintenance (such as power-on setting, upgrade, and data export).
Ensure that the USB cover is tightened when the USB port is not in use.

2.3 Label Description

Symbols

Table 2-3

describes the labels on the SUN2000 enclosure and their meanings.

Table 2-3

Label description

Symbol

Name

Meaning

Running warning

Potential hazards exist
after the SUN2000 is
powered on. Take
protective measures when
operating the SUN2000.

Burn warning

Do not touch a running
SUN2000 because it
generates high
temperatures on the shell.

Summary of Contents for SUN2000-43KTL-IN-C1




































































































Search results

Summary of Contents for SUN2000-43KTL-IN-C1

Reviews:

Brands by name

Popular brands

Huawei SUN2000-43KTL-IN-C1, User Manual

Search results

Summary of Contents for SUN2000-43KTL-IN-C1

Reviews:

Brands by name

Popular brands