Huawei SUN2000-10KTLM1 User Manual Download Page 52

Page: 52 / 124

WARNING

● Do not connect loads between the SUN2000 and the battery.
● The battery cables should be connected correctly. That is, the positive and

negative terminals of the battery connect to the positive and negative battery

terminals on the SUN2000 respectively. Otherwise, the SUN2000 may be

damaged, or even fire could happen.

NO TICE

● During the installation of batteries and the SUN2000, the positive or negative

terminals of batteries may be short-circuited to ground if the power cable is

not properly installed or routed. In this case, an AC or DC short circuit may

occur and damage the SUN2000. The caused device damage is not covered

under any warranty.

● The cabling distance between the battery and the SUN2000 should be less than

or equal to 10 meters (recommended: within 5 meters).

Procedure

Step 1 Assemble the positive and negative connectors by referring to

5.4 Installing DC

input power cables

D ANGER

● The battery voltage may result in serious injury. Use dedicated insulation tools

when connecting cables.

● Ensure that cables are correctly connected between the battery terminal and

the battery switch, and between the battery switch and the SUN2000 battery

terminal.

NO TICE

Cables with high rigidity, such as armored cables, are not recommended as battery

cables, because poor contact may be caused by the bending of the cables.

Step 2 Insert the positive and negative connectors into corresponding battery terminals

on the SUN2000.

NO TICE

After the positive and negative connectors snap into place, pull the battery cables

back to ensure that they are connected securely.

SUN2000-(3KTL-10KTL)-M1

User Manual

5 Electrical Connections

Issue 02 (2020-11-20)

Summary of Contents for SUN2000-10KTLM1





























































































































Search results

Summary of Contents for SUN2000-10KTLM1

Reviews:

Related manuals for SUN2000-10KTLM1

Brands by name

Popular brands

Huawei SUN2000-10KTLM1, User Manual

Search results

Summary of Contents for SUN2000-10KTLM1

Reviews:

Related manuals for SUN2000-10KTLM1

Brands by name

Popular brands