Huawei SUN2000-10KTLM1 User Manual Download Page 68

Page: 68 / 124

6.2 SUN2000 power-on

Important Notes

NO TICE

Before turning on the AC switch between the SUN2000 and the power grid, check

that the AC voltage is within the specified range using a multimeter.

Procedure

Step 1 If a battery is connected, turn on the battery switch.

Step 2 Turn on the AC switch between the SUN2000 and the power grid.

NO TICE

If the DC is on and the AC is off, the SUN2000 reports a Grid Failure alarm. The

SUN2000 starts normally only after the fault is automatically rectified.

Step 3 (Optional) Remove the locking screw from the DC switch.

Figure 6-1 Removing the locking screw from a DC switch

Step 4 Turn on the DC switch (if any) between the PV string and the SUN2000.

Step 5 Turn on the DC switch at the bottom of the SUN2000.

Step 6 Wait for about 1 minute and observe the LED indicators on the SUN2000 to check

its running status.

Table 6-2 LED indicator description

Category

Status

Meaning

Running

indication

LED1

LED2

N/A

Steady green

The SUN2000 is operating in grid-

tied mode.

SUN2000-(3KTL-10KTL)-M1

User Manual

6 Commissioning

Issue 02 (2020-11-20)

Summary of Contents for SUN2000-10KTLM1





























































































































Search results

Summary of Contents for SUN2000-10KTLM1

Reviews:

Related manuals for SUN2000-10KTLM1

Brands by name

Popular brands

Huawei SUN2000-10KTLM1, User Manual

Search results

Summary of Contents for SUN2000-10KTLM1

Reviews:

Related manuals for SUN2000-10KTLM1

Brands by name

Popular brands