Huawei RRU5303 Installation Manual Download Page 57 | Manualshive

Page: 57 / 135

background image

RRU5303
Installation Guide

7 Installing the RRU

Issue Draft B (2018-05-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

49

7.2 Installing the RRU on a Pole

One or more RRUs can be installed on a pole.

7.2.1 Installing a Single RRU

This section describes the procedure and precautions for installing a single RRU on a pole.

Prerequisites

Before you install an RRU on a pole secured on a tower, the RRU and its mounting kits are
hoisted onto the tower. For details, see 6.1 Hoisting an RRU onto a Tower.

The hoist clamp on the main bracket is secured properly.



Do not stand an RRU upright because the RF ports cannot support the weight of the RRU.



Place a foam pad or cardboard under an RRU to protect the RRU housing from damage
during the installation.

Procedure

Step 1

Determine a position for installing the mounting kits.



If the RRU is installed on a tower, determine a position for installing the mounting kits
according to the instructions in 3.5.1 Clearance for a Single RRU.



If the RRU is installed on the ground, determine a position for installing the mounting
kits according to Figure 7-3.

«
...
55
56
57
58
59
...
»

Summary of Contents for RRU5303








































































































































Reviews:

No comments

Related manuals for RRU5303

Brand: E-fly Pages: 16

Brand: DayTronic Pages: 22

Brand: DayTronic Pages: 414

Brand: Laird Pages: 38

Brand: Laird Pages: 5

Brand: Ultratec Pages: 33

Brand: DirectConnect Pages: 2

CS ME-02 Series

Brand: pizzato Pages: 12

Brand: ADEMCO Pages: 4

Brand: Maverick Pages: 122

Brand: Warren rupp Pages: 19

SUPERREMOTE UR19A

Brand: X10 Pages: 17

Brand: Sunricher Pages: 3

All Sport 1600 Series

Brand: Daktronics Pages: 92

Brand: Geeetech Pages: 48

SmartLoop KTSL-FC1-UV-KO

Brand: Keystone Pages: 2

Brand: AMD Pages: 12

Brand: EastLink Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands