Huawei RRU User Manual Download Page 39

Page: 39 / 100

2.2.1 Appearance of the SRXU

The SRXU features a modular structure with its ports at the module bottom and on the cabling
cavity.

Figure 2-3

shows the SRXU. On the left is a front view of the SRXU, and on the right is a side

view of the SRXU.

Figure 2-3

SRXU

2.2.2 LEDs on the SRXU

The LEDs, on the LED panel of the SRXU, indicate the running status of the SRXU.

For the positions of the LEDs on the SRXU, refer to

2.2.3 Panels of the SRXU

Table 2-3

describes the LEDs and their status.

Table 2-3

LEDs on the SRXU

Label

Color

Status

Description

RUN

Green

The module has power input,
yet the module is faulty.

OFF

The module has no power input,
or the module is faulty.

1s ON, 1s OFF

The module is operational.

0.5s ON, 0.5s OFF

Software is being loaded to the
module.

ALM

Red

The module is reporting alarms.

OFF

The module is operational.

CPRI_W

Red/green

ON (green)

The CPRI link is normal.

ON (red)

The optical module receives
local alarms related to LOS.

0.5s ON, 0.5s OFF
(red)

The CPRI link is out of lock.

RRU
User Guide

2 RRU and SRXU Hardware

Issue 01 (2008-04-18)

Huawei Proprietary and Confidential

2-7

Summary of Contents for RRU





































































































Search results

Summary of Contents for RRU

Reviews:

Related manuals for RRU

Brands by name

Popular brands

Huawei RRU, User Manual

Search results

Summary of Contents for RRU

Reviews:

Related manuals for RRU

Brands by name

Popular brands