Huawei RRU User Manual Download Page 67

Page: 67 / 100

Figure 3-8

Minimal space requirements of one RRU with and without the SRXU (unit: mm)

The minimal space around the equipment is as follows:

300 mm under the equipment for cabling. It is recommended that the space is 1,200 mm
between the equipment bottom and the ground for easy maintenance.

600 mm in front of the equipment for maintenance.

200 mm above the equipment for maintenance.

400 mm on the left of the equipment for maintenance.

100 mm on the right of the equipment for maintenance.

When two RRUs need to be combined, space requirements of each RRU must be met. In addition,
the space between the two RRUs should stay within the range shown in

Figure 3-9

Space requirements of two combined RRUs (unit: mm)

The space between the two RRUs is as follows:

RRU
User Guide

3 Installing RRU and SRXU Hardware

Issue 01 (2008-04-18)

Huawei Proprietary and Confidential

3-9

Summary of Contents for RRU





































































































Search results

Summary of Contents for RRU

Reviews:

Related manuals for RRU

Brands by name

Popular brands

Huawei RRU, User Manual

Search results

Summary of Contents for RRU

Reviews:

Related manuals for RRU

Brands by name

Popular brands